908E624_10 Datasheet, PDF (8/40 Pages) Freescale Semiconductor, Inc – Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers

ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
All characteristics are for the analog chip only. Refer to the 68HC908EY16 data sheet for characteristics of the microcontroller
chip. Characteristics noted under conditions 9.0 V ≤ V_SUP ≤ 16 V, - 40°C ≤ T_J ≤ 125°C unless otherwise noted. Typical values
noted reflect the approximate parameter mean at T_A = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SYSTEM RESETS AND INTERRUPTS
Low-Voltage Reset (LVR)
Threshold
V _LVRON
V
3.6
4.0
4.4
Low-Voltage Interrupt (LVI)
Threshold
Hysteresis
High-Voltage Interrupt (HVI)
Threshold
Hysteresis
VOLTAGE REGULATOR ⁽¹⁰⁾
V _LVI
5.7
V _{LVI_HYS}
—
V _HVI
18
V _{HVI_HYS}
—
6.0
1.0
19.25
220
V
6.6
—
20.5
V
—
mV
Normal Mode Output Voltage
2.0 mA < I_DD < 50 mA, 5.5 V < V_SUP < 27 V
Normal Mode Output Current Limitation ⁽¹¹⁾
Dropout Voltage
V_SUP = 4.9 V, I_DD = 50 mA
Stop Mode Output Voltage ⁽¹²⁾
Stop Mode Regulator Current Limitation
Line Regulation
Normal Mode, 5.5 V < V_SUP < 27 V, I_DD = 10 mA
Stop Mode, 5.5 V < V_SUP < 27 V, I_DD = 2.0 mA
V _DDRUN
V
4.75
5.0
5.25
I_DDRUN
50
V _DDDROP
—
110
200
mA
V
0.1
0.2
V _DDSTOP
4.75
5.0
5.25
V
I_DDSTOP
4.0
8.0
14
mA
V_LRRUN
—
V_{LR STOP}
—
mV
20
150
10
100
Load Regulation
Normal Mode, 1.0 mA < I_DD < 50 mA, V_SUP = 18 V
Stop Mode, 1.0 mA < I_DD < 5.0 mA, V_SUP = 18 V
Over-temperature Pre-Warning (Junction) ⁽¹³⁾
Thermal Shutdown Temperature (Junction) ⁽¹³⁾
Temperature Threshold Difference
T_SD - T_PRE
V_LRRUN
—
V_LDSTOP
—
mV
40
150
40
150
T _PRE
120
135
160
°C
T _SD
155
170
—
°C
ΔT _SD-T _PRE
°C
20
30
45
Notes
10. Specification with external capacitor 2.0 μF< C < 10 μF and 200 mΩ ≤ ESR ≤ 10 Ω. Capacitor value up to 47 μF can be used.
11. Total V_DD regulator current. A 5.0 mA current for current sense operational amplifier is included. Digital output supplied from VDD.
12. When switching from Normal to Stop mode or from Stop mode to Normal mode, the output voltage can vary within the output voltage
specification.
13. This parameter is guaranteed by process monitoring but not production tested
908E624
8
Analog Integrated Circuit Device Data
Freescale Semiconductor