XRT73LC04A_08 Datasheet, PDF (13/64 Pages) Exar Corporation – 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT

.
REV. 1.0.2
OPERATING MODE SELECT
PIN #
52
NAME
HOST/(HW)
TYPE
I
XRT73LC04A
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
DESCRIPTION
HOST-Hardware Mode Select:
This input pin is used to enable or disable the Microprocessor Serial
Interface (e.g., consisting of the SDI, SDO, SClk, and CS pins).
Setting this input pin "High" enables the Microprocessor Serial Interface
(e.g. configures the XRT73LC04A to operate in the HOST Mode). In this
mode, configure the XRT73LC04A via the Microprocessor Serial Inter-
face. When the XRT73LC04A is operating in the HOST Mode, then it
ignores the states of many of the discrete input pins. Setting this input
pin "Low" disables the Microprocessor Serial Interface (e.g., configures
the XRT73LC04A to operate in the Hardware Mode). In this mode, many
of the external input control pins are functional. (Internally Pulled-up)
CONTROL AND ALARM INTERFACE
PIN #
NAME
TYPE
36
MRing_0
I
20
MRing_1
1
MRing_2
17
MRing_3
35
MTIP_0
I
21
MTIP_1
2
MTIP_2
16
MTIP_3
48
DMO_0
O
26
DMO_1
133
DMO_2
11
DMO_3
46
TAOS_0
I
45
TAOS_1
135
TAOS_2
136
TAOS_3
64
RLOS_0
O
67
RLOS_1
117
RLOS_2
114
RLOS_3
65
RLOL_0
O
68
RLOL_1
116
RLOL_2
113
RLOL_3
DESCRIPTION
Monitor Ring Input - Channel (n):
The bipolar line output signal from TRing_(n) can be connected to this
pin via a 270-ohm resistor in order to check for line driver failure. This
pin is internally pulled "High".
Monitor Tip Input - Channel (n):
The bipolar line output signal from TTIP_(n) can be connected to this pin
via a 270-ohm resistor in order to check for line driver failure. This pin is
internally pulled "High".
Drive Monitor Output - Channel (n):
If no transmitted AMI signal is present on MTIP_(n) and MRing_(n) input
pins for 128±32 TxClk periods, then DMO_(n) toggles and remains
"High" until the next AMI signal is detected.
Transmit All Ones Select - Channel (n):
A "High" on this pin causes the Transmit Section, within Channel (n), to
generate and transmit a continuous AMI all “1’s" pattern onto the line.
The frequency of this "1’s" pattern is determined by TxClk_(n).
This input pin is ignored if the XRT73LC04A is operating in the HOST
Mode.
NOTE: This pin should be tied to GND if the XRT73LC04A is going to be
operating in the HOST Mode, (internally pulled-down).
Receive Loss of Signal Output Indicator - Channel (n):
This output pin toggles "High" if Channel (n) has detected a Loss of Sig-
nal Condition in the incoming line signal.
The criteria that the XRT73LC04A uses to declare an LOS Condition
depends upon whether the device is operating in the E3 or STS-1/DS3
Mode.
Receive Loss of Lock Output Indicator - Channel (n):
This output pin toggles "High" if Channel (n) has detected a Loss of Lock
Condition. Channel (n) declares an LOL (Loss of Lock) condition if the
recovered clock frequency deviates from the Reference Clock frequency
(available at the EXClk_(n) input pin) by more than 0.5%.
9