RHFAC244D03V Datasheet, PDF (3/27 Pages) List of Unclassifed Manufacturers – DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
J
GDIP1-T24 or CDIP2-T24
24
K
GDFP2-F24 or CDFP3-F24
24
L
GDIP3-T24 or CDIP4-T24
24
R
GDIP1-T20 or CDIP2-T20
20
S
GDFP2-F20 or CDFP3-F20
20
X
See figure 1
20
Z
GDFP1-G20
20
2
CQCC1-N20
20
3
CQCC1-N28
28
Dual-in-line
Flat pack
Dual-in-line
Dual-in-line
Flat pack
Flat pack
Flat pack
Square leadless chip carrier
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (VCC) .................................................................................. -0.5 V dc to +7.0 V dc
DC input voltage range (VIN) ................................................................................ -0.5 V dc to VCC + 0.5 V dc
DC output voltage range (VOUT) ........................................................................... -0.5 V dc to VCC + 0.5 V dc
Clamp diode current (IIK, IOK) ............................................................................... ±20 mA
DC output current (per output pin) ....................................................................... ±50 mA
DC VCC or GND current (per output pin) .............................................................. ±25 mA 4/
Maximum power dissipation (PD) ......................................................................... 500 mW
Storage temperature range (TSTG) ....................................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds):
Case outline X ................................................................................................... +260°C
All other case outlines except case X ................................................................ +245°C
Thermal resistance, junction-to-case (θJC) ........................................................... See MIL-STD-1835
Junction temperature (TJ) .................................................................................... +175°C 5/
1.4 Recommended operating conditions. 2/ 3/ 6/
Supply voltage range (VCC) .................................................................................. +2.0 V dc to +6.0 V dc
Input voltage range (VIN) ...................................................................................... +0.0 V dc to VCC
Output voltage range (VOUT)................................................................................. +0.0 V dc to VCC
Case operating temperature range (TC) ............................................................... -55°C to +125°C
Input rise or fall times (tr, tf):
Device type 01:
VCC = 3.6 V and 5.5 V .................................................................................... 0 to 8 ns/V
Device type 02:
Data (VCC = 3.6 V and 5.5 V) ......................................................................... 0 to 10 ns/V
mOE (VCC = 3.6 V and 5.5 V) ....................................................................... 0 to 5 ns/V
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Unless otherwise noted, all voltages are referenced to GND.
3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range
of -55°C to +125°C.
4/ For devices with multiple VCC or GND pins, this value represents the total VCC or GND current.
5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in
accordance with method 5004 of MIL-STD-883.
6/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data
retention implies no input transition and no stored data loss with the following conditions: VIH ≥ 70% VCC, VIL ≤ 30% VCC,
VOH ≥ 70% VCC @ -20 µA, VOL ≤ 30% VCC @ 20 µA.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
K
5962-87552
SHEET
3