RHFAC244D03V Datasheet, PDF (17/27 Pages) List of Unclassifed Manufacturers – DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

TABLE IIA. Electrical test requirements.
Test requirements
Subgroups
(in accordance with
MIL-STD-883,
method 5005, table I)
Subgroups
(in accordance with
MIL-PRF-38535, table III)
Device
class M
Device
class Q
Device
class V
Interim electrical
parameters (see 4.2)
---
---
1
Final electrical
parameters (see 4.2)
1/ 1, 2, 3, 7,
8, 9
1/ 1, 2, 3, 7,
8, 9
2/, 3/ 1, 2, 3, 7,
8, 9, 10, 11
Group A test
requirements (see 4.4)
1, 2, 3, 4, 7,
8, 9, 10, 11
1, 2, 3, 4, 7,
8, 9, 10, 11
1, 2, 3, 4, 7,
8, 9, 10, 11
Group C end-point electrical
parameters (see 4.4)
1, 2, 3
1, 2, 3
3/ 1, 2, 3, 7,8,
9, 10, 11
Group D end-point electrical
parameters (see 4.4)
1, 2, 3
1, 2, 3
1, 2, 3
Group E end-point electrical
parameters (see 4.4)
1, 7, 9
1, 7, 9
1, 7, 9
1/ PDA applies to subgroup 1.
2/ PDA applies to subgroups 1, 7, and deltas.
3/ Delta limits, as specified in table IIB, shall be required where specified, and the delta limits shall be
completed with reference to the zero hour electrical parameters.
TABLE IIB. Burn-in and operating life test, delta parameters (+25°C). 1/
Parameter 2/
Supply current
Input current low level
Input current high level
Output voltage low level
(VCC = 5.5 V, IOL = 24 mA)
Output voltage high level
(VCC = 5.5 V, IOH = -24 mA)
Symbol
ICCH, ICCL, ICCZ
IIL
IIH
VOL
VOH
Delta limits
±300 nA
±20 nA
±20 nA
±0.04 V
±0.20 V
1/ This table is representation of what vendor CAGE F8859 has experienced and
is guaranteed and not meant to be construed as a quality assurance requirement
for any other vendor.
2/ These parameters shall be recorded before and after the required burn-in and
life tests to determine the delta limits.
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
MIL-STD-883.
b. TA = +125°C, minimum.
c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
K
5962-87552
SHEET
17