RHFAC14K01V Datasheet, PDF (3/24 Pages) List of Unclassifed Manufacturers – STANDARD MICROCIRCUIT DRAWING

1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
C
GDIP1-T14 or CDIP2-T14
14
D
GDFP1-F14 or CDFP2-F14
14
2
CQCC1-N20
20
X
CDFP3-F14
14
Dual-in-line
Flat pack
Leadless chip carrier
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (V_CC) .................................................................................. -0.5 V dc to +7.0 V dc
DC input voltage range (V_IN) ................................................................................ -0.5 V dc to V_CC + 0.5 V dc
DC output voltage range (V_OUT) ........................................................................... -0.5 V dc to V_CC + 0.5 V dc
Clamp diode current (I_IK, I_OK)................................................................................ ±20 mA
DC output current (I_OUT) ....................................................................................... ±50 mA
DC V_CC or GND current (per pin) ......................................................................... ±50 mA
Maximum power dissipation (P_D) ........................................................................ 500 mW
Storage temperature range (T_STG) ....................................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds):
Case outline X ................................................................................................. +260°C
Other case outlines (except case outline X)..................................................... +245°C
Thermal resistance, junction-to-case (θ_JC) ........................................................... See MIL-STD-1835
Junction temperature (T_J) .................................................................................... 175°C 4/
1.4 Recommended operating conditions. 2/ 3/ 5/
Supply voltage range (V_CC) .................................................................................. +2.0 V dc to +6.0 V dc
Input voltage range (V_IN) ...................................................................................... 0.0 V dc to V_CC
Output voltage range (V_OUT)................................................................................. 0.0 V dc to V_CC
Minimum high level input voltage (V_IH) ................................................................. 2.1 V at V_CC = 3.0 V
3.15 V at V_CC = 4.5 V
3.85 V at V_CC = 5.5 V
Maximum low level input voltage (V_IL).................................................................. 0.9 V at V_CC = 3.0 V
1.35 V at V_CC = 4.5 V
1.65 V at V_CC = 5.5 V
Case operating temperature range (T_C) ............................................................... -55°C to +125°C
1.5 Radiation features.
Device type 01:
Total dose (dose rate = 50 – 300 rads (Si)/s) .................................................. 300 krads (Si)
Single Event Latchup (SEL)............................................................................. ≥ 93 MeV-cm²/mg
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Unless otherwise specified, all voltages are referenced to GND.
3/ The limits for the parameters specified herein shall apply over the full specified V_CC range and case temperature range
of -55°C to +125°C.
4/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in
accordance with method 5004 of MIL-STD-883.
5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data
retention implies no input transition and no stored data loss with the following conditions: V_IH ≥ 70% V_CC, V_IL ≤ 30% V_CC, V_OH
≥ 70% V_CC @ -20 µA V_OL ≤ 30% V_CC @ 20 µA.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
B
5962-87624
SHEET
3