HCPL-7710-000E Datasheet, PDF (6/18 Pages) AVAGO TECHNOLOGIES LIMITED – 40 ns Propagation Delay, CMOS Optocoupler

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option 060)
        
Description
Symbol
Installation classification per DIN VDE 0110/1.89, Table 1
  for rated mains voltage ≤150 V rms
  for rated mains voltage ≤300 V rms
  for rated mains voltage ≤450 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b†
  V_IORM x 1.875 = V_PR, 100% Production
  Test with t_m = 1 sec, Partial Discharge < 5 pC
Input to Output Test Voltage, Method a†
  V_IORM x 1.5 = V_PR, Type and Sample Test,
  t_m = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage†
(Transient Overvoltage, t_ini = 10 sec)
Safety Limiting Values
  (Maximum values allowed in the event of a failure,
  also see Thermal Derating curve, Figure 11.)
   Case Temperature
   Input Current
   Output Power
Insulation Resistance at T_S, V₁₀ = 500 V
V_IORM
V_PR
V_PR
V_IOTM
T_S
I_S,INPUT
P_S,OUTPUT
R_IO
HCPL-7710
Option 060
HCPL-0710
Option 060 Units
I-IV
I-IV
I-IV
I-III
I-III
55/100/21
55/100/21
2
2
630
560
V peak
1181
1050
V peak
945
840
V peak
6000
4000
V peak
175
230
600
≥10⁹
150
°C
150
mA
600
mW
≥10⁹
Ω
†Refer to the front of the optocoupler section of the Isolation and Control Component Designer’s Catalog, under Product Safety Regulations sec-
tion IEC/EN/DIN EN 60747-5-2, for a detailed description.
Note: These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be
ensured by means of protective circuits.
Note: The surface mount classification is Class A in accordance with CECC 00802.
Absolute Maximum Ratings
Parameter
Storage Temperature
Ambient Operating Temperature
Supply Voltages
Input Voltage
Output Voltage
Input Current
Average Output Current
Lead Solder Temperature
Solder Reflow Temperature Profile
Symbol
Min.
Max.
Units
T_S
–55
125
°C
T_A
–40
+100
°C
V_DD1, V_DD2
0
6.0
Volts
V_I
–0.5
V_DD1 +0.5 Volts
V_O
–0.5
V_DD2 +0.5 Volts
I_I
–10
+10
mA
I_O
10
mA
260°C for 10 sec., 1.6 mm below seating plane
See Solder Reflow Temperature Profile Section
Recommended Operating Conditions
Parameter
Ambient Operating Temperature
Supply Voltages
Logic High Input Voltage
Logic Low Input Voltage
Input Signal Rise and Fall Times

Symbol
Min.
T_A
–40
V_DD1, V_DD2 4.5
V_IH
2.0
V_IL
0.0
t_r, t_f
Max.
Units
+100
°C
5.5
V
V_DD1
V
0.8
V
1.0
ms