BQ24153A_14 Datasheet, PDF (7/46 Pages) Texas Instruments – Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support

www.ti.com
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0C – OCTOBER 2010 – REVISED JULY 2013
ELECTRICAL CHARACTERISTICS (continued)
Circuit of Figure 2, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), T_J = –40°C to 125°C, T_J = 25°C for typical values
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
PWM
Voltage from BOOT pin to SW pin
During charge or boost operation
Internal top reverse blocking MOSFET on-
resistance
I_IN(LIMIT) = 500 mA, Measured from VBUS to PMID
Internal top N-channel Switching MOSFET on-
resistance
Internal bottom N-channel MOSFET on-
resistance
Measured from PMID to SW,
V_BOOT – V_SW= 4V
Measured from SW to PGND
f_(OSC)
Oscillator frequency
Frequency accuracy
D_(MAX)
D_(MIN)
Maximum duty cycle
Minimum duty cycle
Synchronous mode to non-synchronous mode
transition current threshold⁽³⁾
Low-side MOSFET cycle-by-cycle current sensing
CHARGE MODE PROTECTION
V_{OVP_IN_USB}
V_{OVP-IN_DYN}
Input VBUS OVP threshold voltage
(bq24153A/8)
V_{(OVP_IN_USB)} hysteresis (bq24153A/8)
Input VBUS OVP threshold voltage (bq24156A)
VBUS threshold to turn off converter during charge
VBUS falling from above V_{(OVP_IN_USB)}
Threshold over VBUS to turn off converter during
charge
V_{(OVP_IN_DYN)} hysteresis (bq24156A/9)
VBUS falling from above V_{(OVP_IN_DYN)}
V_OVP
Output OVP threshold voltage
V_(OVP) hysteresis
V_(CSOUT) threshold over V_(OREG) to turn off charger
during charge
Lower limit for V_(CSOUT) falling from above V_(OVP)
I_LIMIT
Cycle-by-cycle current limit for charge
Charge mode operation
V_SHORT
Trickle to fast charge threshold
V_SHORT hysteresis
V_(CSOUT) rising
V_(CSOUT) falling below V_SHORT
I_SHORT
Trickle charge charging current
V_(CSOUT) ≤ V_SHORT)
BOOST MODE OPERATION FOR V_BUS (OPA_MODE = 1, HZ_MODE = 0, bq24153A/8 only)
V_{BUS_B}
Boost output voltage (to VBUS pin)
2.5V < V_(CSOUT) < 4.5 V
Boost output voltage accuracy
Including line and load regulation
I_BO
I_BLIMIT
V_BUSOVP
V_BATMAX
V_BATMIN
Maximum output current for boost
Cycle by cycle current limit for boost
Overvoltage protection threshold for boost
(VBUS pin)
V_{BUS_B} = 5.05 V, 2.5 V < V_(CSOUT) < 4.5 V
V_{BUS_B} = 5.05 V, 2.5 V < V_(CSOUT) < 4.5 V
Threshold over VBUS to turn off converter during
boost
V_BUSOVP hysteresis
Maximum battery voltage for boost (CSOUT
pin)
V_BUS falling from above V_BUSOVP
V_(CSOUT) rising edge during boost
V_BATMAX hysteresis
Minimum battery voltage for boost (CSOUT pin)
V_(CSOUT) falling from above V_BATMAX
During boosting
Before boost starts
Boost output resistance at high-impedance
mode (From VBUS to PGND)
CD = 1 or HZ_MODE = 1
PROTECTION
T_SHTDWN)
Thermal trip
Thermal hysteresis
T_CF
Thermal regulation threshold
t_32S
32 second watchdog (WD) timer
t_15M
15 minute safety timer
Charge current begins to reduce
32 Second or HOST mode
15 Minute mode
MIN TYP MAX UNIT
6.5
V
180
250
120
250 mΩ
110
–10%
0
3.0
99.5%
100
210
10%
MHz
mA
6.3
6.5
6.7
V
170
mV
9.57
9.8
10
140
110
117
121
%V_OREG
11
1.8
2.4
3.0
A
2.0
2.1
2.2
V
100
mV
20
30
40 mA
5.05
–3%
200
1.0
V
3%
mA
A
5.8
6.0
6.2
V
162
mV
4.75
4.9 5.05
V
200
mV
2.5
V
2.9 3.05
V
217
kΩ
165
10
120
15
32
12
°C
s
15 m
(3) Bottom N-channel FET always turns on for ~30 ns and then turns off if current is too low.
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: bq24153A bq24156A bq24158 bq24159