BQ24153A_14 Datasheet, PDF (5/46 Pages) Texas Instruments – Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support

www.ti.com
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0C – OCTOBER 2010 – REVISED JULY 2013
RECOMMENDED OPERATING CONDITIONS
V_BUS
V_BUS
T_J
Supply voltage, bq24153A/8
Supply voltage, bq24156A/9
Operating junction temperature range
MIN
NOM
4
4
–40
MAX
6 ⁽¹⁾
9 ⁽¹⁾
125
UNIT
V
V
°C
(1) The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BOOST or SW pins. A tight
layout minimizes switching noise.
ELECTRICAL CHARACTERISTICS
Circuit of Figure 2, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), T_J = –40°C to 125°C, T_J = 25°C for typical values
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
INPUT CURRENTS
VBUS > VBUS(min), PWM switching
10
mA
I_(VBUS)
I_lgk
VBUS supply current control
Leakage current from battery to VBUS pin
VBUS > VBUS(min), PWM NOT switching
0°C < T_J < 85°C, CD=1 or HZ_MODE=1
0°C < T_J < 85°C, V_(CSOUT) = 4.2 V, High Impedance
mode, VBUS = 0 V
5
15
23 μA
5 μA
Battery discharge current in High Impedance
mode, (CSIN, CSOUT, SW pins)
0°C < T_J < 85°C, V_(CSOUT) = 4.2 V, High Impedance
mode, V = 0 V, SCL, SDA, OTG = 0 V
or 1.8 V
23 μA
VOLTAGE REGULATION
V_(OREG)
Output regulation voltage programable range
Voltage regulation accuracy
Operating in voltage regulation, programmable
T_A = 25°C
3.5
–0.5%
–1%
4.44
V
0.5%
1%
CURRENT REGULATION (FAST CHARGE)
bq24153A/8, V_(SHORT) ≤ V_(CSOUT) < V_(OREG),
550
VBUS > V_(SLP), R_(SNS) = 68 mΩ, LOW_CHG=0,
Programmable
I_O(CHARGE) Output charge current programmable range
bq24156A/9, V_(SHORT) ≤ V_(CSOUT) < V_(OREG),
550
VBUS > V_(SLP), R_(SNS) = 68 mΩ, LOW_CHG=0,
Programmable
1250 mA
1550 mA
Low charge current (default after POR in 15 min V_SHORT ≤ V_CSOUT < V_OREG, VBUS >V_SLP, R_SNS= 68
mode) for bq24153A/6A/8/9
mΩ, LOW_CHG=1, OTG=High for bq24153A/8
325
350 mA
Regulation accuracy of the voltage across
R_(SNS) (for charge current regulation)
V_(IREG) = I_O(CHARGE) × R_(SNS)
WEAK BATTERY DETECTION
37.4 mV ≤ V_(IREG)< 44.2mV
44.2 mV ≤ V_(IREG)
–3.5%
–3%
3.5%
3%
V_(LOWV)
Weak battery voltage threshold programmable Adjustable using I²C control
range^{2 (1)}
3.4
3.7
V
Weak battery voltage accuracy
–5%
5%
Hysteresis for V_(LOWV)
Deglitch time for weak battery threshold
CD, OTG and SLRST PIN LOGIC LEVEL
Battery voltage falling
Rising voltage, 2-mV over drive, t_RISE = 100 ns
100
mV
30
ms
V_IL
Input low threshold level
V_IH
Input high threshold level
I_(bias)
Input bias current
CHARGE TERMINATION DETECTION
Voltage on control pin is 5 V
0.4
V
1.3
V
1.0 µA
I_(TERM)
Termination charge current programmable
range
Deglitch time for charge termination
Regulation accuracy for termination current
across R_(SNS)
V_{(IREG_TERM)} = I_O(TERM) × R_(SNS)
V_(CSOUT) > V_(OREG) – V_(RCH),
VBUS > V_(SLP), R_(SNS) = 68 mΩ, Programmable
Both rising and falling, 2-mV overdrive,
t_RISE, t_FALL = 100 ns
3.4 mV ≤ V_{(IREG_TERM)} ≤ 6.8 mV
6.8 mV < V_{(IREG_TERM)} ≤ 17 mV
17 mV < V_{(IREG_TERM)} ≤ 27.2 mV
50
–15%
–10%
–5.5%
400 ^mA
30
ms
15%
10%
5.5%
(1) While in 15-min mode, if a battery that is charged to a voltage higher than this voltage is inserted, the charger enters Hi-Z mode and
awaits I²C commands.
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: bq24153A bq24156A bq24158 bq24159