LM3S9D96 Datasheet, PDF (438/1407 Pages) Texas Instruments – ARM and Thumb are registered trademarks and Cortex is a trademark

General-Purpose Input/Outputs (GPIOs)
Register 16: GPIO Pull-Down Select (GPIOPDR), offset 0x514
The GPIOPDR register is the pull-down control register. When a bit is set, a weak pull-down resistor
on the corresponding GPIO signal is enabled. Setting a bit in GPIOPDR automatically clears the
corresponding bit in the GPIO Pull-Up Select (GPIOPUR) register (see page 436).
Important: All GPIO pins are configured as GPIOs and tri-stated by default (GPIOAFSEL=0,
GPIODEN=0, GPIOPDR=0, GPIOPUR=0, and GPIOPCTL=0, with the exception of the
pins shown in the table below. A Power-On-Reset (POR) or asserting RST puts the pins
back to their default state.
Table 8-10. GPIO Pins With Non-Zero Reset Values
GPIO Pins
PA[1:0]
PA[5:2]
PB[3:2]
PC[3:0]
Default State
UART0
SSI0
I²C0
JTAG/SWD
GPIOAFSEL GPIODEN GPIOPDR GPIOPUR
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
GPIOPCTL
0x1
0x2
0x3
0x1
Note:
The GPIO commit control registers provide a layer of protection against accidental
programming of critical hardware peripherals. Protection is provided for the NMI pin (PB7)
and the four JTAG/SWD pins (PC[3:0]). Writes to protected bits of the GPIO Alternate
Function Select (GPIOAFSEL) register (see page 430), GPIO Pull Up Select (GPIOPUR)
register (see page 436), GPIO Pull-Down Select (GPIOPDR) register (see page 438), and
GPIO Digital Enable (GPIODEN) register (see page 441) are not committed to storage
unless the GPIO Lock (GPIOLOCK) register (see page 443) has been unlocked and the
appropriate bits of the GPIO Commit (GPIOCR) register (see page 444) have been set.
GPIO Pull-Down Select (GPIOPDR)
GPIO Port A (APB) base: 0x4000.4000
GPIO Port A (AHB) base: 0x4005.8000
GPIO Port B (APB) base: 0x4000.5000
GPIO Port B (AHB) base: 0x4005.9000
GPIO Port C (APB) base: 0x4000.6000
GPIO Port C (AHB) base: 0x4005.A000
GPIO Port D (APB) base: 0x4000.7000
GPIO Port D (AHB) base: 0x4005.B000
GPIO Port E (APB) base: 0x4002.4000
GPIO Port E (AHB) base: 0x4005.C000
GPIO Port F (APB) base: 0x4002.5000
GPIO Port F (AHB) base: 0x4005.D000
GPIO Port G (APB) base: 0x4002.6000
GPIO Port G (AHB) base: 0x4005.E000
GPIO Port H (APB) base: 0x4002.7000
GPIO Port H (AHB) base: 0x4005.F000
GPIO Port J (APB) base: 0x4003.D000
GPIO Port J (AHB) base: 0x4006.0000
Offset 0x514
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
reserved
Type RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
reserved
PDE
Type RO
RO
RO
RO
RO
RO
RO
RO
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
438
January 23, 2012
Texas Instruments-Production Data