AM1707_16 Datasheet, PDF (29/200 Pages) Texas Instruments – AM1707 ARM® Microprocessor

www.ti.com
AM1707
SPRS637E – FEBRUARY 2010 – REVISED JUNE 2014
3.6.17 Ethernet Media Access Controller (EMAC)
Table 3-19. Ethernet Media Access Controller (EMAC) Terminal Functions
SIGNAL NAME
PIN
No.
ZKB
TYPE ⁽¹⁾
PULL ⁽²⁾
MUXED
DESCRIPTION
RMII
AHCLKR0/RMII_MHZ_50_CLK/GP2[14]/BOOT[11]
A4
I/O
IPD McASP0, GPIO, BOOT
EMAC 50-MHz
clock input or output
AXR0[6]/RMII_RXER/ACLKR2/GP3[6]
D7
I
IPD
EMAC RMII receiver
error
AXR0[5]/RMII_RXD[1]/AFSX2/GP3[5]
AXR0[4]/RMII_RXD[0]/AXR2[1]/GP3[4]
C7
I
IPD
B7
I
IPD
EMAC RMII receive
data
AXR0[3]/RMII_CRS_DV/AXR2[2]/GP3[3]
A7
I
IPD McASP0, McASP2, GPIO
EMAC RMII carrier
sense data valid
AXR0[2]/RMII_TXEN/AXR2[3]/GP3[2]
D8
O
IPD
EMAC RMII transmit
enable
AXR0[1]/RMII_TXD[1]/ACLKX2/GP3[1]
AXR0[0]/RMII_TXD[0]/AFSR2/GP3[0]
C8
O
IPD
B8
O
IPD
EMAC RMII trasmit
data
MDIO
AXR0[8]/MDIO_D/GP3[8]
AXR0[7]/MDIO_CLK/GP3[7]
B6
I/O
A6
O
IPU
McASP0, GPIO
IPD
MDIO serial data
MDIO clock
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the the signal name
highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured
function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different
types (i.e., input versus output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor
3.6.18 Multimedia Card/Secure Digital (MMC/SD)
Table 3-20. Multimedia Card/Secure Digital (MMC/SD) Terminal Functions
SIGNAL NAME
PIN
No.
ZKB
TYPE ⁽¹⁾
PULL ⁽²⁾
MUXED
DESCRIPTION
EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1]
EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2]
R9
O
P9
I/O
IPU
MMCSD Clock
EMIFA, UHPI, GPIO
IPU
MMCSD Command
EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/BOOT[13] M15 I/O
IPU
EMIFA, UHPI, GPIO,
BOOT
EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6]
N13 I/O
IPU
EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5]
N15 I/O
IPU
EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4]
EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3]
P13 I/O
P15 I/O
IPU
EMIFA, UHPI, GPIO MMC/SD data
IPU
EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2]
R13 I/O
IPU
EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1]
R15 I/O
IPU
EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/BOOT[12]
T13
I/O
IPU
EMIFA, UHPI, GPIO,
BOOT
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the the signal name
highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured
function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different
types (i.e., input versus output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor
Copyright © 2010–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: AM1707
Device Overview
29