TM4C129CNCZAD Datasheet, PDF (1657/1772 Pages) Texas Instruments – Tiva Microcontroller

Tiva^™ TM4C129CNCZAD Microcontroller
Table 28-2. Signals by Pin Number (continued)
Pin Number
M1
M2
M3
M4
M8
M9
M10
M11
M12
M16
M17
M18
N1
N2
Pin Name
PC5
C1+
EPI0S6
RTCCLK
T7CCP1
U7Tx
PC4
C1-
EPI0S7
T7CCP0
U7Rx
PQ7
U1RI
PQ3
EPI0S23
SSI3XDAT1
T7CCP1
GND
GND
GND
VDD
VDD
PG3
I2C2SDA
SSI2XDAT2
HIB
PM4
T4CCP0
TMPR3
U0CTS
PJ6
U4RTS
PR2
I2C2SCL
M0PWM2
Pin Type
I/O
I
I/O
O
I/O
O
I/O
I
I/O
I/O
I
I/O
I
I/O
I/O
I/O
I/O
-
-
-
-
-
I/O
I/O
I/O
O
I/O
I/O
I/O
I
I/O
O
I/O
I/O
O
Buffer Type Description
TTL
GPIO port C bit 5.
Analog Analog comparator 1 positive input.
TTL
EPI module 0 signal 6.
TTL
Buffered version of the Hibernation module's 32.768-kHz clock.
This signal is not output when the part is in Hibernate mode and
before being configured after power-on reset.
TTL
16/32-Bit Timer 7 Capture/Compare/PWM 1.
TTL
UART module 7 transmit.
TTL
GPIO port C bit 4.
Analog Analog comparator 1 negative input.
TTL
EPI module 0 signal 7.
TTL
16/32-Bit Timer 7 Capture/Compare/PWM 0.
TTL
UART module 7 receive.
TTL
GPIO port Q bit 7.
TTL
UART module 1 Ring Indicator modem status input signal.
TTL
GPIO port Q bit 3.
TTL
EPI module 0 signal 23.
TTL
SSI Module 3 Bi-directional Data Pin 1 (SSI3RX in Legacy SSI
Mode).
TTL
16/32-Bit Timer 7 Capture/Compare/PWM 1.
Power Ground reference for logic and I/O pins.
Power Ground reference for logic and I/O pins.
Power Ground reference for logic and I/O pins.
Power Positive supply for I/O and some logic.
Power Positive supply for I/O and some logic.
TTL
GPIO port G bit 3.
OD
I²C module 2 data.
TTL
SSI Module 2 Bi-directional Data Pin 2.
TTL
An output that indicates the processor is in Hibernate mode.
TTL
GPIO port M bit 4.
TTL
16/32-Bit Timer 4 Capture/Compare/PWM 0.
TTL
Tamper signal 3.
TTL
UART module 0 Clear To Send modem flow control input signal.
TTL
GPIO port J bit 6.
TTL
UART module 4 Request to Send modem flow control output line.
TTL
GPIO port R bit 2.
OD
I²C module 2 clock. Note that this signal has an active pull-up. The
corresponding port pin should not be configured as open drain.
TTL
Motion Control Module 0 PWM 2. This signal is controlled by
Module 0 PWM Generator 1.
June 18, 2014
Texas Instruments-Production Data
1657