TCA9543A_15 Datasheet, PDF (1/32 Pages) Texas Instruments – TCA9543A Low Voltage 2-Channel I2C Bus Switch With Interrupt Logic And Reset

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
TCA9543A
SCPS206A – MARCH 2014 – REVISED FEBRUARY 2015
TCA9543A Low Voltage 2-Channel I²C Bus Switch With Interrupt Logic And Reset
1 Features
•1 1-of-2 Bidirectional Translating Switches
• I²C Bus and SMBus Compatible
• Two Active-Low Interrupt Inputs
• Active-Low Interrupt Output
• Active-Low Reset Input
• Two Address Pins Allowing up to Four TCA9543A
Devices on the I²C Bus
• Channel Selection Via I²C Bus, in Any
Combination
• Power-up With All Switch Channels Deselected
• Low R_ON Switches
• Allows Voltage-Level Translation Between
1.8-V, 2.5-V, 3.3-V, and 5-V Buses
• No Glitch on Power-up
• Supports Hot Insertion
• Low Standby Current
• Operating Power-Supply Voltage Range of 1.65-V
to 5.5-V
• 5.5-V Tolerant Inputs
• 0 to 400-kHz Clock Frequency
• Latch-Up Performance Exceeds 100-mA Per
JESD78
• ESD Protection Exceeds JESD 22
– 4000-V Human-Body Model (A114-A)
– 1500-V Charged-Device Model (C101)
2 Applications
• Servers
• Routers (Telecom Switching Equipment)
• Factory Automation
• Products With I²C Slave Address Conflicts (e.g.
Multiple, Identical Temp Sensors)
3 Description
The TCA9543A is a dual bidirectional translating
switch controlled by the I²C bus. The SCL/SDA
upstream pair fans out to two downstream pairs, or
channels. Either individual SCn/SDn channel or both
channels can be selected, determined by the
contents of the programmable control register. Two
interrupt inputs (INT1–INT0), one for each of the
downstream pairs, are provided. One interrupt output
(INT) acts as an AND of the two interrupt inputs.
An active-low reset (RESET) input allows the
TCA9543A to recover from a situation where one of
the downstream I²C buses is stuck in a low state.
Pulling RESET low resets the I²C state machine and
causes both of the channels to be deselected, as
does the internal power-on reset function.
The pass gates of the switches are constructed such
that the VCC terminal can be used to limit the
maximum high voltage, which will be passed by the
TCA9543A. This allows the use of different bus
voltages on each pair, so that 1.8-V, 2.5-V, or 3.3-V
parts can communicate with 5-V parts without any
additional protection. External pull-up resistors pull
the bus up to the desired voltage level for each
channel. All I/O terminals are 5.5-V tolerant.
Device Information⁽¹⁾
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TCA9543A
TSSOP (14)
SOIC (14)
5.00 mm × 4.40 mm
8.65 mm × 3.91 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Simplified Application Diagram
I2C or SMBus
Master
(e.g. Processor)
SDA
SCL
INT
VCC
RESET
Channel 0
SD0
SC0
INT0
Slaves A0, A1...AN
TCA9543A
A0
A1
GND
SD1 ^{Channel 1}
SC1
INT1
Slaves B0, B1...BN
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.