AM1806_15 Datasheet, PDF (170/245 Pages) Texas Instruments – AM1806 ARM® Microprocessor

AM1806
SPRS658F – FEBRUARY 2010 – REVISED MARCH 2014
www.ti.com
BYTE ADDRESS
0x01E0 0462
0x01E0 0463
0x01E0 0464
0x01E0 0466
0x01E0 046C
0x01E0 0480
0x01E0 0482
0x01E0 0483
0x01E0 0484
0x01E0 0486
0x01E0 0487
0x01E0 0488
0x01E0 048A
0x01E0 048B
0x01E0 048C
0x01E0 048E
0x01E0 048F
0x01E0 0490
0x01E0 0492
0x01E0 0493
0x01E0 0494
0x01E0 0496
0x01E0 0497
0x01E0 0498
0x01E0 049A
0x01E0 049B
Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued)
ACRONYM
REGISTER DESCRIPTION
TXFIFOSZ
Transmit Endpoint FIFO Size
(Index register set to select Endpoints 1-4 only)
RXFIFOSZ
Receive Endpoint FIFO Size
(Index register set to select Endpoints 1-4 only)
TXFIFOADDR
Transmit Endpoint FIFO Address
(Index register set to select Endpoints 1-4 only)
RXFIFOADDR
Receive Endpoint FIFO Address
(Index register set to select Endpoints 1-4 only)
HWVERS
Hardware Version Register
Target Endpoint 0 Control Registers, Valid Only in Host Mode
TXFUNCADDR
Address of the target function that has to be accessed through the associated Transmit
Endpoint.
TXHUBADDR
Address of the hub that has to be accessed through the associated Transmit Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXFUNCADDR
Address of the target function that has to be accessed through the associated Receive
Endpoint.
RXHUBADDR
Address of the hub that has to be accessed through the associated Receive Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXHUBPORT
Port of the hub that has to be accessed through the associated Receive Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
Target Endpoint 1 Control Registers, Valid Only in Host Mode
TXFUNCADDR
Address of the target function that has to be accessed through the associated Transmit
Endpoint.
TXHUBADDR
Address of the hub that has to be accessed through the associated Transmit Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXFUNCADDR
Address of the target function that has to be accessed through the associated Receive
Endpoint.
RXHUBADDR
Address of the hub that has to be accessed through the associated Receive Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXHUBPORT
Port of the hub that has to be accessed through the associated Receive Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
Target Endpoint 2 Control Registers, Valid Only in Host Mode
TXFUNCADDR
Address of the target function that has to be accessed through the associated Transmit
Endpoint.
TXHUBADDR
Address of the hub that has to be accessed through the associated Transmit Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXFUNCADDR
Address of the target function that has to be accessed through the associated Receive
Endpoint.
RXHUBADDR
Address of the hub that has to be accessed through the associated Receive Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
RXHUBPORT
Port of the hub that has to be accessed through the associated Receive Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
Target Endpoint 3 Control Registers, Valid Only in Host Mode
TXFUNCADDR
Address of the target function that has to be accessed through the associated Transmit
Endpoint.
TXHUBADDR
Address of the hub that has to be accessed through the associated Transmit Endpoint. This is
used only when full speed or low speed device is connected via a USB2.0 high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used
only when full speed or low speed device is connected via a USB2.0 high-speed hub.
170 Peripheral Information and Electrical Specifications
Copyright © 2010–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: AM1806