SMH4042A Datasheet, PDF (3/28 Pages) Summit Microelectronics, Inc. – Distributed Power Hot-Swap Controller for CompactPCI

SMH4042A
PIN DESCRIPTIONS
A0 (8)
HST_3V_MON (23)
Address 0 is not used by the memory array. It can be
connected to ground or left floating. It must not be
connected VCC.
A1, A2 (10, 11)
Address inputs 1 and 2 are used to set the two-bit device
address of the memory array. The state of these inputs
will determine the device address for the memory if it is
on a two-wire bus with multiple memories with the same
device type identifier.
This input monitors the host 3.3V supply and it is used as
a reference for the circuit breaker comparator. If VCC3
falls below VTRIP then SGNL_VLD# is de-asserted, the
high side drivers are disabled, and LOCAL_PCI_RST# is
asserted.
ISLEW (3)
A Diode-connected NFET input. It may be used to adjust
the 250V/s default slew rate of the high-side driver
outputs.
SCL (19)
PCI_RST# (17)
The SCL input is used to clock data into and out of the
memory array. In the write mode, data must remain stable
while SCL is HIGH. In the read mode, data is clocked out
on the falling edge of SCL.
SDA (18)
The SDA pin is a bidirectional pin used to transfer data into
and out of the memory array. Data changing from one
state to the other may occur only when SCL is LOW,
except when generating START or STOP conditions.
SDA is an open-drain output and may be wire-ORed with
any number of open-drain outputs.
CARD_3V_MON (21)
This input monitors the card-side 3.3V supply. If the input
falls below VTRIP then the HEALTHY# and SGNL_VLD#
outputs are de-asserted and the reset outputs are driven
active.
CARD_5V_MON (25)
This input monitors the card-side 5V supply. If the input
falls below VTRIP then the HEALTHY# and SGNL_VLD#
outputs are de-asserted and the reset outputs are driven
active.
CBI_3 (24)
CBI_3 is the circuit breaker input for the low supply. With
a series resistor placed in the supply path between VCC3
and CBI_3, the circuit breaker will trip whenever the
voltage across the resistor exceeds 50mV.
CBI_5 (1)
CBI_5 is the circuit breaker input for the supply voltage.
With a series resistor placed in the supply path between
the 5V early power and CBI_5, the circuit breaker will trip
whenever the voltage across the resistor exceeds 50mV.
A TTL level reset input signal from the host interface. A
high to low transition (held low longer than 40ns) will
initiate a reset sequence. The LOCAL_PCI_RST# and
LOCAL_PCI_RST outputs will be driven active for a
minimum period of tPURST. If the PCI_RST# input is still
held low after tPURST times out the reset outputs will
continue to be driven until PCI_RST# is released.
PWR_EN (7)
A TTL level input that allows the host to enable or disable
the power to the individual card. During initial power up
this signal would start in a low state, and then be driven
high during software initialization. If this signal is driven
low then the power supply control outputs will be driven
into the inactive state and the reset signals asserted. In
a “non-High Availability” system this input can be tied
high. The PWR_EN input is also used to reset the
SMH4042A circuit breakers. After an over-current condi-
tion is detected the VGATE outputs can be turned back
on by first taking PWR_EN low then returning it high.
VSEL (6)
A TTL level input used to determine which of the host
power supply inputs will be monitored for valid voltage and
reset generation. This is a static input and the pin should
be tied to VCC or ground through a resistor. VSEL is high
for 3.3V power. VSEL is low for 5V or mixed mode power.
VCC (28)
The power supply input. It is monitored for power integrity.
If it falls below the 5V sense threshold (VTRIP) and the
VSEL input is low then the SGNL_VLD# and HEALTHY#
signals are de-asserted, the high side drivers disabled,
and reset outputs asserted. On a CompactPCI board this
must be connected to early power.
SUMMIT MICROELECTRONICS, Inc.
2070 9.1 5/27/03
3