M16C6C_15 Datasheet, PDF (79/100 Pages) Renesas Technology Corp – RENESAS MCU

M16C/6C Group
5. Electrical Characteristics
V_CC1 = V_CC2 = 3 V
Table 5.41 Electrical Characteristics (2)
V_CC1 = V_CC2 = 2.7 to 3.3 V, V_SS = 0 V at T_opr = −20°C to 85°C/−40°C to 85°C, f_(BCLK) = 32 MHz unless otherwise specified.
Symbol
Parameter
Measuring Condition
Standard
Min. Typ. Max.
Unit
I_CC
Power supply current High-speed mode f_(BCLK) = 32 MHz
In single-chip, mode,
XIN = 4 MHz (square wave), PLL multiplied by 8
125 kHz on-chip oscillator stopped
the output pin are
open and other pins
are V_SS
f_(BCLK) = 32 MHz ⁽²⁾
XIN = 4 MHz (square wave), PLL multiplied by 8
125 kHz on-chip oscillator stopped
f_(BCLK) = 16 MHz
XIN = 16 MHz (square wave)
125 kHz on-chip oscillator stopped
40 MHz on-chip Main clock stopped
27.0
mA
27.7
mA
13.0
mA
oscillator mode
125 kHz on-chip
40 MHz on-chip oscillator on,
divide-by-4 (f_(BCLK) = 10 MHz)
125 kHz on-chip oscillator stopped
Main clock stopped
17.0
mA
oscillator mode
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator on, no division
FMR22 = 1 (slow read mode)
450.0
μA
Low-power mode
f_(BCLK) = 32 MHz
In low-power mode
FMR 22 = FMR23 = 1
On flash memory ⁽¹⁾
f_(BCLK) = 32 MHz
In low-power mode
160.0
μA
40.0
μA
Wait mode
On RAM ⁽¹⁾
Main clock stopped
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator on
Peripheral clock operating
T_opr = 25°C
f_(XCIN) = 32 MHz (oscillation capacity High)
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
20.0
μA
8.0
μA
Stop mode
During flash
memory program
During flash
memory erase
Peripheral clock operating
T_opr = 25°C
f_(XCIN) = 32 kHz (oscillation capacity Low)
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
Peripheral clock operating
T_opr = 25°C
Main clock stopped
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
Peripheral clock stopped
T_opr = 25°C
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
V_CC1 = 3.0 V
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
V_CC1 = 3.0 V
6.0
μA
2.0
μA
20.0
mA
30.0
mA
Notes:
1.
2.
This indicates the memory in which the program to be executed exists.
This applies when using one A/D converter (fAD = 25MHz), with the ADSTBY bit for the unused A/D converter set to 0 (A/D
operation stopped (standby).
R01DS0034EJ0210 Rev.2.10
Jul 31, 2012
Page 79 of 96