M16C6C_15 Datasheet, PDF (61/100 Pages) Renesas Technology Corp – RENESAS MCU

M16C/6C Group
5. Electrical Characteristics
V_CC1 = V_CC2 = 5 V
Table 5.21 Electrical Characteristics (3)
V_CC1 = V_CC2 = 4.2 to 5.5 V, V_SS = 0 V at T_opr = −20°C to 85°C/−40°C to 85°C, f_(BCLK) = 32 MHz unless otherwise specified.
Symbol
Parameter
Measuring Condition
Standard
Min. Typ. Max.
Unit
I_CC
Power supply current High-speed mode f_(BCLK) = 32 MHz
XIN = 4 MHz (square wave), PLL multiplied by 8
In single-chip, mode,
125 kHz on-chip oscillator stopped
the output pin are
open and other pins
are V_SS
f_(BCLK) =32 MHz, A/D conversion ⁽²⁾
XIN = 4 MHz (square wave), PLL multiplied by 8
125 kHz on-chip oscillator stopped
27.0
mA
27.7
mA
f_(BCLK) = 16 MHz
XIN = 16 MHz (square wave)
13.0
mA
125 kHz on-chip oscillator stopped
40 MHz on-chip Main clock stopped
oscillator mode
40 MHz on-chip oscillator on,
divide-by-4 (f_(BCLK) = 10 MHz)
17.0
mA
125 kHz on-chip oscillator stopped
125 kHz on-chip Main clock stopped
oscillator mode
40 MHz on-chip oscillator stopped,
125 kHz on-chip oscillator on, no division
500.0
μA
FMR22 = 1 (slow read mode)
Low-power mode f_(BCLK) = 32 kHz
In low-power mode
FMR22 = FMR23 = 1
160.0
μA
On flash memory ⁽¹⁾
f_(BCLK) = 32 kHz
In low-power mode
45.0
μA
On RAM ⁽¹⁾
Wait mode
Main clock stopped
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator on
21.0
μA
Peripheral clock operating
T_opr = 25°C
f_(XCIN) = 32 kHz (oscillation capacity High)
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
11.0
μA
Peripheral clock operating
T_opr = 25°C
f_(XCIN) = 32 kHz (oscillation capacity Low)
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
6.0
μA
Peripheral clock operating
T_opr = 25°C
Stop mode
Main clock stopped
40 MHz on-chip oscillator stopped
125 kHz on-chip oscillator stopped
2.2
μA
Peripheral clock stopped
During flash
memory program
T_opr = 25°C
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
V_CC1 = 5.0 V
20.0
mA
During flash
memory erase
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
V_CC1 = 5.0 V
30.0
mA
Notes:
1. This indicates the memory in which the program to be executed exists.
2. This applies when using one A/D converter (fAD = 25MHz), with the ADSTBY bit for the unused A/D converter set to 0 (A/D
operation stopped (standby).
R01DS0034EJ0210 Rev.2.10
Jul 31, 2012
Page 61 of 96