M16C30L Datasheet, PDF (149/166 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Electrical characteristics
Mitsubishi microcomputers
M16C / 30L Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table 1.26.3. Electrical characteristics (referenced to VCC = 3.0V to 3.6V, VSS = 0V at Topr = – 20^oC to
85^oC / – 40^oC to 85^oC (Note 1), f(XIN) = 16MHZ unless otherwise specified)
Symbol
Parameter
Measuring condition
HIGH output P00 to P07, P10 to P17, P20 to P27,
VOH
voltage
P30 to P37, P40 to P47, P50 to P57,
P60 to P67, P72 to P77, P80 to P84, ^{IOH = -1mA}
P86, P87, P90 to P97, P100 to P107 ^{VCC = 3.3V}
Standard
Min Typ. Max. ^Unit
2.8
V
VOH
HIGH output voltage XOUT
HIGHPOWER
LOWPOWER
IOH = -0.1mA, VCC = 3.3V
IOH = -50µA, VCC = 3.3V
HIGH output voltage XCOUT
HIGHPOWER
LOWPOWER
With no load applied, VCC = 3.3V
With no load applied, VCC = 3.3V
LOW output P00 to P07 ,P10 to P17, P20 to P27,
VOL
voltage
P30 to P37, P40 to P47, P50 to P57, _{IOL = 1mA}
P60 to P67, P70 to P77, P80 to P84, _{VCC = 3.3V}
P86, P87, P90 to P97, P100 to P107
2.8
2.8
V
2.8
V
1.6
0.5
V
HIGHPOWER IOL = 0.1mA, VCC = 3.3V
VOL
LOW output voltage XOUT
LOWPOWER IOL = 50µA, VCC = 3.3V
LOW output voltage XCOUT
HIGHPOWER
LOWPOWER
With no load applied, VCC = 3.3V
With no load applied, VCC = 3.3V
0.5
V
0.5
0
V
0
VT+-VT-
Hysteresis
HOLD, RDY, TA0IN to TA2IN,
TB1IN, TB2IN, INT0 to INT2, NMI,
ADTRG, CTS0 to CTS2, SCL, SDA
CLK0 to CLK2,TA2OUT,
KI0 to KI3, RxD0 to RxD2
VCC = 3.3V
0.2
0.8
V
VT+-VT-
IIH
Hysteresis RESET
VCC = 3.3V
HIGH input
current
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47 ,P50 to P57,
P60 to P67, P70 to P77, P80 to P87,
P90 to P97, P100 to P107,
XIN, RESET, CNVss, BYTE
VI = 3V
VCC = 3.3V
0.2
1.8
V
4.0
µA
LOW input P00 to P07, P10 to P17, P20 to P27,
current
P30 to P37, P40 to P47, P50 to P57,
I IL
P60 to P67, P70 to P77, P80 to P87, VI = 0V
P90 to P97, P100 to P107,
VCC = 3.3V
XIN, RESET, CNVss, BYTE
-4.0
µA
R PULLUP
R fXIN
R fXCIN
V RAM
Icc
Pull-up
resistance
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P67, P72 to P77, P80 to P84,
P86, P87, P90 to P97 ,P100 to P107
VI = 0V
VCC = 3.3V
Feedback resistance XIN
Feedback resistance XCIN
RAM retention voltage
Power supply current
When clock is stopped
In single-chip
mode, the
output pins are
open and other
pins are VSS
f(XIN) = 16MHz,
Square wave, no division
f(XCIN) = 32kHz, VCC = 3.3V
Square wave
f(XCIN) = 32kHz, VCC = 3.3V
When a WAITinstruction
is executed.
Oscillation capacity High (Note 2)
20.0 100.0 500.0 kΩ
3.0
MΩ
10.0
MΩ
2.0
V
12.5 25.0 mA
40.0
µA
5.8
µA
f(XCIN) = 32kHz, VCC = 3.3V
When a WAIT instruction
is executed.
Oscillation capacity Low (Note 2)
2.7
µA
Note 1: Specify a product of -40°C to 85°C to use it.
Note 2: With one timer operated using fC32.
Topr = 25°C, VCC = 3.3V
when clock is stopped
Topr = 85°C, VCC = 3.3V
when clock is stopped
0.1 2.0
µA
0.4 100
148