PS219B2-AS Datasheet, PDF (5/11 Pages) Powerex Power Semiconductors – Dual-In-Line Intelligent Power Module 5 Amperes/600 Volts

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 [phone] www.pwrx.com
PS219B2-S, PS219B2-AS, PS219B2-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
5 Amperes/600 Volts
Electrical and Mechanical Characteristics, T_j = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ. Max. Units
Inverter Part
Collector-Emitter Saturation Voltage
V_CE(sat) V_D = V_DB = 15V, I_C = 5A, V_IN = 5V, T_j = 25°C
V_D = V_DB = 15V, I_C = 5A, V_IN = 5V, T_j = 125°C
Diode Forward Voltage
V_EC
-I_C = 5A, V_IN = 0V
Switching Times
t_on
t_rr
V_CC = 300V, V_D = V_DB = 15V,
t_C(on)
I_C = 5A, T_j = 125°C,
t_off
V_IN = 0 ⇔ 5V, Inductive Load
t_C(off)

Collector-Emitter Cutoff Current
I_CES
V_CE = V_CES, T_j = 25°C
V_CE = V_CES, T_j = 125°C
—
—
—
0.75
—
—
—
—
—
—
1.50
1.60
1.70
1.35
0.30
0.35
1.40
0.30
—
—
2.00
2.10
2.20
1.95
—
0.55
2.00
0.60
1.0
10
Volts
Volts
Volts
µs
µs
µs
µs
µs
mA
mA
Control (Protection) Part
Circuit Current I_D
V_IN = 0V, V_D = 15V
Total of V_P1-V_NC, V_N1-V_NC
—
—
2.80
mA
V_IN = 5V, V_D = 15V
Total of V_P1-V_NC, V_N1-V_NC
—
—
2.80
mA
I_DB V_IN = 0V, V_D = V_DB = 15V Each Part of V_UFB-U, V_VFB-V, V_WFB-W
—
—
0.10
mA
V_IN = 5V, V_D = V_DB = 15V Each Part of V_UFB-U, V_VFB-V, V_WFB-W
—
—
0.10
mA
Fault Output Voltage
V_FOH
V_SC = 0V, F_O Terminal Pull-up to 5V by 10kΩ
4.9
—
—
Volts
V_FOL
V_SC = 1V, I_FO = 1mA
—
—
0.95 Volts
Input Current
I_IN
V_IN = 5V
0.70
1.00
1.50
mA
Short Circuit Trip Level
V_SC(ref)
V_D = 15V^*4
0.43 0.48 0.53 Volts
Temperature Output
V_OT
LVIC Temperature = 90°C
2.63 2.77 2.91 Volts
Pull Down R = 5kΩ^*6
LVIC Temperature = 25°C
0.88
1.13
1.39 Volts
Control Supply
UV_DBt
Trip Level, T_j ≤ 125°C
7.0
10.0
12.0
Volts
Under-voltage Protection
UV_DBr
Reset Level, T_j ≤ 125°C
7.0
10.0
12.0
Volts
UV_Dt
Trip Level, T_j ≤ 125°C
10.3
—
12.5 Volts
UV_Dr
Reset Level, T_j ≤ 125°C
10.8
—
13.0 Volts
Fault Output Pulse Width^*5
t_FO
20
—
—
µs
ON Threshold Voltage
V_th(on)
Applied between
—
2.1
2.6
Volts
OFF Threshold Voltage
V_th(off)
U_P, V_P, W_P-V_NC,
0.8
1.3
—
Volts
ON/OFF Threshold Hysteresis Voltage V_th(hys)
U_N, V_N, W_N-V_NC
0.35 0.65
—
Volts
Bootstrap Diode Forward Voltage^*7
V_F
I_F = 10mA,
1.1
1.7
2.3
Volts

Including Voltage Drop by Limiting Resistor
Built-in Limiting Resistance
R
For Bootstrap Circuit
80
100
120
Ω
*4 Short Circuit protection is functioning only for N-side IGBTs. Please select the value of the external shunt resistor such that the SC trip level is less than 1.7 times the current rating.
*5 Fault signal, FO, outputs when SC or UV protection works. FO pulse width is different for each protection mode. At SC failure, FO pulse width is a fixed width (=min. 20µs), however, at UV
failure, FO outputs continuously until recovering from UV state. Minimum FO pulse width is 20µs.
12/11 Rev. 0
5