BUK221-50DY Datasheet, PDF (7/16 Pages) NXP Semiconductors – Dual channel high-side TOPFET

Philips Semiconductors
BUK221-50DY
Dual channel high-side TOPFET™
Table 6: Static characteristics…continued
Limits are valid for −40 °C ≤ T_mb ≤ +150 °C and typical values for T_mb = 25 °C unless otherwise specified.
Symbol Parameter
Conditions
Min Typ
I_L(oc)
load open circuit current
V_LG = 3.5 V; per channel
V_LG = 16 V; per channel
-
−22
-
−200
R_L(oc)
open circuit load resistor
V_S = 5 V; connected externally;
per channel; Figure 10
-
10
Undervoltage ^[9]
V_BG(uv)
battery-ground undervoltage
[11] ₂
4.2
V_BG(uv)(hys) battery-ground undervoltage
hysteresis
-
0.5
Overvoltage ^[9]
V_BG(ov)
battery-ground overvoltage
[12] ₃₅
40
V_BG(ov)(hys) battery-ground overvoltage hysteresis
I_G(ov)
overvoltage operating current
V_BG = 45 V; per channel
0.2 1
-
1
Overload protection
I_L(lim)
self-limiting load current
Overtemperature protection ^[9][10]
V_BG ≥ 8 V; V_BL = V_BG; Figure 7
8
12
T_j(th)
threshold junction temperature
[13] _{150 170}
T_j(th)(hys)
threshold junction temperature
hysteresis
3
10
Status ^[9]
V_SG(CL)
V_SG(L)
status-ground clamping voltage
status-ground low voltage
I_S = 100 µA
I_S = 100 µA; Figure 6
I_S = 250 µA
5.5 7
-
0.7
-
-
I_S(off)
status leakage current
R_S
status resistor
V_SG = 5 V
T_mb = 150 °C
-
-
T_mb = 25 °C
-
0.1
V_SG = 5 V; connected externally; ^[14] -
47
Figure 10
Max
−40
−300
-
5.3
1.5
45
2
2.5
16
190
20
8.5
0.9
1.1
10
1
-
Unit
µA
µA
kΩ
V
V
V
V
mA
A
°C
°C
V
V
V
µA
µA
kΩ
[1] For a high-side switch, the load pin voltage goes negative with respect to the ground during the turn-off of an inductive load. This
negative voltage is clamped by the device.
[2] 9 V ≤ V_BG ≤ 35 V
[3] This is the current drawn from the supply when both inputs are LOW, and includes leakage current to the loads.
[4] Defined as in ISO10483-1. For comparison purposes only.
[5] This only applies to the R_BLon per channel. The supply and input voltages for the R_BLon tests are continuous. The specified pulse
duration is t_p = 300 µs, and refers only to the applied load current.
[6] R_G is a resistor incorporated internally into the package.
[7] 5.5 V ≤ V_BG ≤ 35 V
[8] An open circuit load can be detected in the off-state and requires an external pull-up resistor, R_L(oc).
[9] See Table 3 “Truth table”
[10] Overtemperature protection is not active during reverse current operation.
[11] Undervoltage sensor causes each output channel to switch off and reset.
[12] Overvoltage sensor causes each output channel to switch off to protect the load.
[13] After cooling below the reset temperature the channel will resume normal operation.
[14] The status output is an open drain transistor and requires an external pull-up resistor, R_S, to indicate a logic HIGH.
9397 750 11167
Product data
Rev. 01 — 16 April 2003
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7 of 16