MN101EFA6 Datasheet, PDF (18/33 Pages) Panasonic Semiconductor – 8-bit Single-chip Microcontroller

MN101EFA6/A5/A1/A0 Series
8-bit Single-chip Microcontroller
PubNo. 216A6-012E
Pins
KEY0
KEY1
KEY2
KEY3
KEY4
KEY5
KEY6
KEY7
LED0
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
LED9
LED10
LED11
LED12
LED13
LED14
LED15
DMOD
MMOD
TSIN0
TSIN1
TSIN2
TSIN3
TSIN4
TSIN5
TSIN6
TSIN7
TSRC
TSOP
Table remarks -: Without function
MN101EF
A6/A1
48pin 44pin
TQFP QFP
MN101EF
A5/A0
I/O
32pin 32pin
SSOP TQFP
Function
Description
44
40
29
26
Input Key interrupt input pins
45
41
30
27
46
42
31
28
47
43
32
29
Input pins for KEY interrupt based on OR condition result of pin
inputs.
These can be set to key input pins by 1-bit with KEY interrupt control
register (KEYT3_1IMD).
When not used for KEY input, these pins can be used as normal I/O
pins.
48
44
1
30
1
1
2
31
2
2
3
32
3
3
4
1
18
16
17
14
Output LED drive pins
19
17
18
15
20
18
19
16
Large current output pins.
Select the large current output by P0LED and PALED registers.
When not used for LED output, these pins can be used as normal I/O
pins.
21
19
20
17
22
20
21
18
23
21
22
19
24
22
23
20
25
23
24
21
44
40
29
26
45
41
30
27
46
42
31
28
47
43
32
29
48
44
1
30
1
1
2
31
2
2
3
32
3
3
4
1
9
8
9
6
Input Mode switch input pins
Set always to V_DD5.
15
14
15
12
Input ROM area switch input pins at start
Set always to V_SS.
44
40
29
26
Input Touch sensor input pins
Input pins for Touch Sensor Timer of 8 channels.
45
41
30
27
These pins are not equipped in MN101EFA1 Set "Used" to corresponding channel by TSTCHSEL register.
and MN101EFA0.
This setup is available regardless of the setting of port control regis-
46
42
31
28
ters. These can be used as normal I/O pins when Touch Sensor
Timer is not used.
47
43
32
29
48
44
1
30
1
1
2
31
2
2
3
32
3
3
4
1
36
34
28
25
Input Touch sensor resistor connect pins.
These are used in the following cases.
These pins are not equipped in MN101EFA1 1. External resistor connection for Touch Sensor Timer
37
35
27
24
Output _{and MN101EFA0.}
Set both TSMD and RSMD of TSTMD register to “1”.
2. The capacitor/resistor connection for Touch Sensor using A/D
converter
Set TSADCNT register.
This setup is available regardless of the setting of port control regis-
ters. These can be used as normal I/O pins when Touch Sensor
Timer is not used.
For the MMOD setup in rewriting the flash memory, refer to [Chapter 16 16.4 User Mode
Microcontroller Rewriting], [Chapter 16 16.5 BOOT Mode Microcontroller Rewriting], [Chap-
ter 16 16.6 Appendix].
..
..
Publication date: November 2014