Y92S-41-200 Datasheet, PDF (17/32 Pages) Omron Electronics LLC – This Compact Cam Positioner, Popular for Its Ease-of-use, Now Comes with Even Better Functions.

Accessories (Order Separately)
E69-C06B Shaft Coupling (for the E6CP) E69-C08B Shaft Coupling (for the E6C3)
22
5.5
5.5
(11)
Four, M3 Hexagon
2.8
(16.4)
2.8 _{socket-head setscrews}
23.6
6.8
6.8
Four, M4 Hexagon
3.5
3.5 ^{socket-head setscrews}
H8PS
E69-C10B Shaft Coupling (for the E6F)
26.2
7.1 (12) 7.1
Four, M4 Hexagon
3.6
(19)
socket-head setscrews
3.6
6H8 dia.15 dia.
8H8 dia.
8H8 dia.19 dia.
10H8 dia.22 dia.
Note: The material is fiber-glass-reinforced _{Note: The material is fiber-glass-reinforced} Note: The material is fiber-glass-reinforced
polybutylene terephthalate resin (PBT).
polybutylene terephthalate resin (PBT).
polybutylene terephthalate resin (PBT).
E69-DF5 Extension Cable
34.6
5,000
37
16.9 dia.
16.9 dia.
(See note 1.) (See note 2.)
(See note 3.)
Note 1: E6F-AG5C-C, E6CP-AG5C-C, and E6C3-AG5C-C Connectors for the H8PS.
Note 2: 6-dia., 12-core shielded cable (cross-sectional area: 0.2 mm², insulation: 1.1 mm dia.), standard length: 5 m
Note 3: Connected to the H8PS Cam Positioner.
Note: Refer to Characteristics on page 4 for the maximum cable length.
The following models are also available: E69-DF10 (10 m), E69-DF15 (15 m), E69-DF20 (20 m), and E69-DF98 (98 m).
Safety Precautions for Encoders
■ Precautions for Correct Use
• Do not subject the E6CP Encoder to oil or water.
• The Encoder consists of high-precision components. Handle it with
utmost care and do not drop it, otherwise malfunctioning may
result.
• When connecting the shaft of the Encoder with a chain timing belt
or gear, connect the chain timing belt or gear with the shaft via a
bearing or coupling as shown in the following diagram.
Chain
sprocket
Bearings
Coupling
Rotary Encoder
• If the decentering or declination value exceeds the tolerance, an
excessive load imposed on the shaft may damage or shorten the
life of the Encoder.
• Do not place excessive loads on the shaft if the shaft is connected
to a gear.
• The tightening torque must not exceed the value given in the table
at the right when the Rotary Encoder is mounted with screws.
• Do not pull wires with a force greater than 29.4 N while the Rotary
Encoder is secured and wired.
Rotary Encoder
Fastening
plate
Cord
29.4 N max.
• Do not subject the shaft to shock. Therefore, do not strike the shaft
or coupling with a hammer when inserting the shaft into the
coupling.
• Make sure there is no foreign matter in the Connector before
connecting it to the Encoder.
Mounting Procedure
1 Insert the shaft into the Coupling.
2 Secure the Encoder.
Do not secure the
Coupling and shaft
with screws at this
time.
Refer to the table for
the maximum
insertion lengths of
the shaft into the
Coupling.
Coupling
E69-C06B
E69-C08B
E69-C10B
Maximum insertion length
5.5 mm
6.8 mm
7.1 mm
3 Secure the Coupling.
Coupling
Tightening torque
E69-C06B 0.25 N·m
E69-C08B 0.44 N·m
E69-C10B 0.44 N·m
4 Connect the power and I/O lines.
5 Turn ON the power and check the
outputs.
Be sure to turn
OFF the Encoder
before connecting
the lines.
17