DS92LV2411 Datasheet, PDF (7/40 Pages) National Semiconductor (TI) – 5-50MHz 24-Bit Channel Link II Serializer and Deserializer

DS92LV2412 Deserializer Pin Descriptions
Pin Name
Pin #
I/O, Type Description
LVCMOS Parallel Interface
DO[7:0]
33, 34, 35,
36, 37, 39,
40, 41
I, STRAP,
O, LVCMOS
Parallel Interface Data Output Pins
For 8–bit RED Display: DO7 = R7 – MSB, DO0 = R0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
DO[15:8]
20, 21, 22,
23, 25, 26,
27, 28
I, STRAP,
O, LVCMOS
Parallel Interface Data Output Pins
For 8–bit GREEN Display: DO15 = G7 – MSB, DO8 = G0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
DO[23:16]
9, 10, 11,
12, 14, 17,
18, 19
I, STRAP,
O, LVCMOS
Parallel Interface Data Input Pins
For 8–bit BLUE Display: DO23 = B7 – MSB, DO16 = B0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
CO1
6
O, LVCMOS Control Signal Output
For Display/Video Application:
CO1 = Data Enable Output
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CO2
8
O, LVCMOS Control Signal Output
For Display/Video Application:
CO2 = Horizontal Sync Output
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CO3
7
O, LVCMOS Control Signal Output
For Display/Video Application:
CO3 = Vertical Sync Output
CO3 is different than CO1 and CO2 because it is limited to 1 transition per 130 clock cycles.
Thus, the minimum pulse width allowed is 130 clock cycle wide.
The CONFIG[1:0] pins have no affect on CO3 signal
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CLKOUT
5
O, LVCMOS Pixel Clock Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7). Data
strobe edge set by RFB.
LOCK
32
O, LVCMOS LOCK Status Output
LOCK = 1, PLL is Locked, outputs are active LOCK = 0, PLL is unlocked, DO[23:0], CO1,
CO2, CO3 and CLKOUT output states are controlled by OSS_SEL (See Table 7). May be
used as Link Status or to flag when Video Data is active (ON/OFF).
PASS
42
O, LVCMOS PASS Output (BIST Mode)
PASS = 1, error free transmission
PASS = 0, one or more errors were detected in the received payload
Route to test point for monitoring, or leave open if unused.
Control and Configuration — STRAP PINS
For a High State, use a 10 kΩ pull up to V_DDIO; for a Low State, the IO includes an internal pull down. The STRAP pins are read upon
power-up and set device configuration. Pin Number listed along with shared data output name in square brackets.
7
www.national.com