COPCH942C Datasheet, PDF (6/26 Pages) National Semiconductor (TI) – 8-Bit CMOS ROM Based Microcontrollers with 1k or 2k

DC Electrical Characteristics (Continued)
COP82XC, COP84XC; −40˚C ≤ T_A ≤ +85˚C unless otherwise specified
Parameter
Condition
Min
Typ
Load Capacitance on D2
Max
1000
Units
pF
Note 8: Rate of voltage change must be less than 0.5V/ms.
Note 9: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 10: The HALT mode will stop CKI from oscillating in the RC and the Crystal configurations. Test conditions: All inputs tied to V_CC, L and G0 — G5 configured
as outputs and set high. The D port set to zero.
Note 11: Except pin G7: +100 mA, −25 mA (COP820C only). Sampled and not 100% tested. Pins G6 and RESET are designed with a high voltage input network
for factory testing. These pins allow input voltages greater than V_CC and the pins will have sink current to V_CC when biased at voltages greater than V_CC (the pins
do not have source current when biased at a voltage below V_CC). The effective resistance to V_CC is 750Ω (typical). These two pins will not latch up. The voltage at
the pins must be limited to less than 14V.
AC Electrical Characteristics
−40˚C ≤ T_A ≤ +85˚C unless otherwise specified
Parameter
Condition
Instruction Cycle Time (tc)
Ext. or Crystal/Resonator
(Div-by 10)
R/C Oscillator Mode
(Div-by 10)
CKI Clock Duty Cycle (Note 12)
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
fr = Max
Rise Time (Note 12)
fr = 10 MHz Ext Clock
Fall Time (Note 12)
fr = 10 MHz Ext Clock
Inputs
t_SETUP
t_HOLD
Output Propagation Delay
t_PD1, t_PD0
SO, SK
All Others
MICROWIRE Setup Time (t_UWS)
MICROWIRE Hold Time (t_UWH)
MICROWIRE Output Propagation
Delay (t_UPD)
Input Pulse Width
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
C_L = 100 pF, R_L = 2.2 kΩ
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
V_CC ≥ 4.5V
2.5V ≤ V_CC < 4.5V
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer Input Low Time
Reset Pulse Width
Note 12: Parameter sampled (not 100% tested).
Min
Typ
1
2.5
3
7.5
40
200
500
60
150
Max
DC
DC
DC
DC
60
12
8
Units
µs
µs
µs
µs
%
ns
ns
ns
ns
ns
ns
0.7
µs
1.75
µs
1
µs
2.5
µs
20
ns
56
ns
220
ns
t_C
t_C
t_C
t_C
1.0
µs
www.national.com
6