MNSCAN18541T-X Datasheet, PDF (5/12 Pages) National Semiconductor (TI) – SERIALLY CONTROLLED ACCESS NETWORK NON-INVERTING LINE DRIVER WITH TRI-STATE OUTPUTS

MNSCAN18541T-X REV 1A0
MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS(Continued)
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: 4.5V to 5.5V, Temp. Range: -55 C to 125 C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED BUT NOT
TESTED.
SYMBOL
IOZH
PARAMETER
Output Leakage
Current
CONDITIONS
VCC=4.5V, VIL=4.5V, VIH (OE)=2.0V
VCC=5.5V, VIL=5.5V, VIH (OE)=2.0V
IOZL
Output Leakage
Current
VCC=4.5V, VIL=0.0V, VIH (OE)=2.0V
VCC=5.5V, VIL=0.0V, VIH (OE)=2.0V
IOS
VIKL
VIKH
CIN
COUT
CPD
VILD
VIHD
VOLP
VOLV
VOHP
VOHV
Output Short
Circuit Current
VCC=5.5V, VIN=5.5V, VOUT=0.0V,
IOS= -100mA
Clamp Diode
Voltage
VCC=4.5V, IKL=-18mA
Clamp Diode
Voltage
VCC=4.5V, IKH=18mA
Input Pin
Capacitance
VCC=5.0V
Output Pin
Capacitance
VCC=5.0V
Power Dissipation VCC=5.0V
Capacitance
Maximum LOW
Dynamic Input
Voltage Level
VCC=5.0V, LOAD: 50pF / 500 OHMS
Minimum HIGH
Dynamic Input
Voltage Level
VCC=5.0V, LOAD: 50pF / 500 OHMS
Maximum High
Output Noise
VCC=5.0V, LOAD: 50pF / 500 OHMS
Minimum Low
Output Noise
VCC=5.0V, LOAD: 50pF / 500 OHMS
Maximum Overshoot VCC=5.0V, LOAD: 50pF / 500 OHMS
Minimum Vcc Droop VCC=5.0V, LOAD: 50pF / 500 OHMS
NOTES
PIN-
NAME
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 OUTPUT
1, 3 INPUT
1, 3 INPUT
6
MIN
MAX
UNIT
SUB-
GROUPS
0.5
uA 1
10
uA 2, 3
0.5
uA 1
10
uA 2, 3
-0.5 uA 1
-10.0 uA 2, 3
-0.5 uA 1
-10.0 uA 2, 3
0
V
1, 2,
3
-1.2 V
1, 2,
3
5.7
V
1, 2,
3
5
pF 4
6
15
pF 4
6
35
pF 4
6, 9 INPUT 0.8
V
4
6, 9 INPUT
2.0
V
4
6, 8 INPUT
6, 8 INPUT
6, 8 INPUT
6, 8 INPUT
0.8
V
4
-0.8 V
4
VOH + V
4
0.8
VOH - V
4
0.8
5