LMH6601_14 Datasheet, PDF (4/37 Pages) National Semiconductor (TI) – LMH6601/LMH6601Q 250 MHz, 2.4V CMOS Operational Amplifier with Shutdown

LMH6601, LMH6601-Q1
SNOSAK9E – JUNE 2006 – REVISED MARCH 2013
www.ti.com
5V ELECTRICAL CHARACTERISTICS (continued)
Single Supply with V_S= 5V, A_V = +2, R_F = 604Ω, SD tied to V⁺, V_OUT = V_S/2, R_L = 150Ω to V^− unless otherwise specified.
Boldface limits apply at temperature extremes. ⁽¹⁾
Symbol
Parameter
Condition
Min ⁽²⁾
Typ ⁽²⁾ Max ⁽²⁾
Units
R_IN
C_IN
+PSRR
Input Resistance
Input Capacitance
Positive Power Supply Rejection
Ratio
0V ≤ V_IN ≤ 3.5V
DC
10
TΩ
1.3
pF
55
59
dB
51
−PSRR
Negative Power Supply Rejection DC
Ratio
53
61
dB
50
CMRR
CMVR
Common Mode Rejection Ratio
Input Voltage Range
DC
CMRR > 50 dB
56
68
dB
53
V^− -0.20
–
V⁺ - 1.5
V
I_CC
Supply Current
VOH1
Output High Voltage
(Relative to V⁺)
Normal Operation
V_OUT = V_S/2
Shutdown
SD tied to ≤ 0.5V ⁽⁵⁾
R_L = 150Ω to V^–
9.6
11.5
13.5
mA
100
nA
–210
–480
–190
VOH2
VOH3
VOL1
Output Low Voltage
(Relative to V^–)
R_L = 75Ω to V_S/2
R_L = 10 kΩ to V^–
R_L = 150Ω to V^–
–190
mV
–60
–12
–110
+5
+45
+125
VOL2
VOL3
R_L = 75Ω to V_S/2
R_L = 10 kΩ to V^–
+120
mV
+5
+45
+125
I_O
I_O_1
Output Current
V_OUT < 0.6V from Respective Source
150
Supply
Sink
180
mA
V_OUT = V_S/2,
V_ID = ±18 mV ⁽⁶⁾
±100
Load
Output Load Rating
THD < −30 dBc, f = 200 kHz,
R_L tied to V_S/2, V_OUT = 4 V_PP
20
Ω
R_O_Enabled Output Resistance
Enabled, A_V = +1
0.2
Ω
R_O_Disabled Output Resistance
Shutdown
>100
MΩ
C_O_Disabled Output Capacitance
Shutdown
5.0
pF
Miscellaneous Performance
VDMAX
Voltage Limit for Disable (Pin 5)
(5)
0
0.5
V
VDMIN
Voltage Limit for Enable (Pin 5)
(5)
4.5
5.0
V
I_i
Logic Input Current (Pin 5)
SD = 5V ⁽⁵⁾
10
pA
V_{_glitch}
Turn-on Glitch
2.2
V
T_on
Turn-on Time
1.4
µs
T_off
Turn-off Time
520
ns
Isolation_OFF Off Isolation
1 MHz, R_L = 1 kΩ
60
dB
T_OL
Overload Recovery
<20
ns
(5) SD logic is CMOS compatible. To ensure proper logic level and to minimize power supply current, SD should typically be less than 10%
of total supply voltage away from either supply rail.
(6) “V_ID” is input differential voltage (input overdrive).
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMH6601 LMH6601-Q1