COP87L88CL Datasheet, PDF(21/34 Page) National Semiconductor (TI) – 8-Bit One-Time Programmable OTP Microcontroller

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

COP87L88CL Datasheet, PDF (21/34 Pages) National Semiconductor (TI) – 8-Bit One-Time Programmable OTP Microcontroller

◁

Memory Map

All RAM ports and registers (except A and PC) are mapped

into data memory address space

Address

Contents

00 to 6F On-Chip RAM bytes

70 to BF Unused RAM Address Space

CB to CF

Timer T2 Lower Byte

Timer T2 Upper Byte

Timer T2 Autoload Register T2RA Lower Byte

Timer T2 Autoload Register T2RA Upper Byte

Timer T2 Autoload Register T2RB Lower Byte

Timer T2 Autoload Register T2RB Upper Byte

Timer T2 Control Register

WATCHDOG Service Register (Reg WDSVR)

MIWU Edge Select Register (Reg WKEDG)

MIWU Enable Register (Reg WKEN)

MIWU Pending Register (Reg WKPND)

Reserved

DD to DF

Port L Data Register

Port L Configuration Register

Port L Input Pins (Read Only)

Reserved for Port L

Port G Data Register

Port G Configuration Register

Port G Input Pins (Read Only)

Port I Input Pins (Read Only)

Port C Data Register

Port C Configuration Register

Port C Input Pins (Read Only)

Reserved for Port C

Port D Data Register

Reserved for Port D

E0 to E5

Reserved

Timer T1 Autoload Register T1RB Lower Byte

Timer T1 Autoload Register T1RB Upper Byte

ICNTRL Register

MICROWIRE Shift Register

Timer T1 Lower Byte

Timer T1 Upper Byte

Timer T1 Autoload Register T1RA Lower Byte

Timer T1 Autoload Register T1RA Upper Byte

CNTRL Control Register

PSW Register

F0 to FB

On-Chip RAM Mapped as Registers

X Register

SP Register

B Register

Reserved

Note Reading memory locations 70-7F Hex will return all ones Reading

other unused memory locations will return undefined data

Addressing Modes

There are ten addressing modes six for operand address-

ing and four for transfer of control

OPERAND ADDRESSING MODES

This is the âânormalââ addressing mode The operand is the

data memory addressed by the B pointer or X pointer

decrement of pointer)

This addressing mode is used with the LD and X instruc-

tions The operand is the data memory addressed by the B

pointer or X pointer This is a register indirect mode that

automatically post increments or decrements the B or X reg-

ister after executing the instruction

Direct

The instruction contains an 8-bit address field that directly

points to the data memory for the operand

Immediate

The instruction contains an 8-bit immediate field as the op-

erand

Short Immediate

This addressing mode is used with the Load B Immediate

instruction The instruction contains a 4-bit immediate field

as the operand

Indirect

This addressing mode is used with the LAID instruction The

contents of the accumulator are used as a partial address

(lower 8 bits of PC) for accessing a data operand from the

program memory

TRANSFER OF CONTROL ADDRESSING MODES

Relative

This mode is used for the JP instruction with the instruction

field being added to the program counter to get the new

program location JP has a range from b31 to a32 to allow

a 1-byte relative jump (JP a 1 is implemented by a NOP

instruction) There are no ââpagesââ when using JP since all

15 bits of PC are used

Absolute

This mode is used with the JMP and JSR instructions with

the instruction field of 12 bits replacing the lower 12 bits of

the program counter (PC) This allows jumping to any loca-

tion in the current 4k program memory segment

Absolute Long

This mode is used with the JMPL and JSR instructions with

the instruction field of 12 bits replacing the lower 12 bits of

the program counter (PC) This allows jumping to any loca-

tion up to 32k in the program memory space

Indirect

This mode is used with the JID instruction The contents of

the accumulator are used as a partial address (lower 8 bits

of PC) for accessing a location in the program memory The

contents of this program memory location serve as a partial

address (lower 8 bits of PC) for the jump to the next instruc-

tion

Note

The VIS is a special case of the Indirect Transfer of Control address-

ing mode where the double byte vector associated with the interrupt

is transferred from adjacent addresses in the program memory into

the program counter (PC) in order to jump to the associated interrupt

service routine

http www national com

▷