UPD789304 Datasheet, PDF (44/64 Pages) NEC – 8-BIT SINGLE-CHIP MICROCONTROLLER

µPD789304, 789306, 789314, 789316
DC Characteristics (TA = –40 to +85°C, VDD = 1.8 to 5.5 V) (3/4)
Parameter
Symbol
Conditions
MIN.
TYP.
MAX.
Unit
Power supply
current^{Note 1}
(Ceramic/crystal
oscillation)
IDD1
5.0 MHz crystal
VDD = 5.0 V ±10%^{Note 2}
oscillation operation
mode
(C1 = C2 = 22 pF)
VDD = 3.0 V ±10%^{Note 3}
VDD = 2.0 V ±10%^{Note 3}
1.8
2.9
mA
0.36
0.9
mA
0.16
0.45
mA
IDD2
5.0 MHz crystal
VDD = 5.0 V ±10%^{Note 2}
oscillation HALT mode
(C1 = C2 = 22 pF)
VDD = 3.0 V ±10%^{Note 3}
VDD = 2.0 V ±10%^{Note 3}
0.96
1.92
mA
0.26
0.76
mA
0.1
0.34
mA
IDD3
32.768 kHz crystal
VDD = 5.0 V ±10%
oscillation operation
mode^{Note 4}
(C3 = C4 = 22 pF,
VDD = 3.0 V ±10%
VDD = 2.0 V ±10%
R1 = 220 kΩ)
30
58
µA
9
26
µA
4
12
µA
IDD4
32.768 kHz LCD
VDD = 5.0 V ±10%
crystal
oscillation
HALT
not
VDD = 3.0 V ±10%
operating
VDD = 2.0 V ±10%
mode^{Note 4}
(C3 = C4 =
22 pF,
LCD
VDD = 5.0 V ±10%
operating
Note 5
VDD = 3.0 V ±10%
R1 = 220 kΩ)
VDD = 2.0 V ±10%
25
48
µA
7
20
µA
4
10
µA
28
57
µA
9.6
27.8
µA
6
16
µA
IDD5
STOP mode^{Note 6}
VDD = 5.0 V ±10%
0.1
10
µA
VDD = 3.0 V ±10%
0.05
5.0
µA
VDD = 2.0 V ±10%
0.05
3.0
µA
Notes 1.
2.
3.
4.
5.
6.
The port current (including the current that flows to the on-chip pull-up resistor) is not included.
High-speed mode operation (when processor clock control register (PCC) is set to 00H)
Low-speed mode operation (when PCC is set to 02H)
When the main system clock is stopped
This is the total current that flows when the LCD controller/driver is operating (LCDON0 = 1, VAON0 =
1, LIPS0 = 1). The power supply current when the LCD is not operating (LCDON0 = 0, VAON0 = 1,
LIPS0 = 0) is included in IDD2.
This is the current when the LCD voltage booster circuit is stopped (LCDON0 = 0, VAON0 = 1).
Remark Unless specified otherwise, the characteristics of alternate-function pins are the same as those of port
pins.
44
Data Sheet U14384EJ1V0DS