PRF18BA471QB5RB Datasheet, PDF (83/104 Pages) Murata Manufacturing Co., Ltd. – POSISTOR for Circuit Protection

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
R90E.pdf
Sep.24,2012
Overheat Sensing Chip Type Specifications and Test Methods
c PRF18/21_471Q Series
No.
Item
1 Resistance Value (25°C)
2 Adhesive Strength
Specification
The resistance value shall be within the specified
tolerance.
There is no sign of exfoliation on electrode.
Test Condition
After applying max. operating voltage for 3 minutes and
leaving for 2 hours in 25°C, measured by applying voltage less
than 1.5VDC. (by a direct current less than 10mA).
EIAJ ET-7403 term 9
Prepare soldered PTC to PCB (**)
and add the force of 5.0N in the direction as shown below.
(PTC=POSISTORr)
PTC
F
F
3 Vibration Resistance
4 Solderability
Normal appearance
Resistance change: not to exceed ±20% (*)
Min. 95% electrode is covered with new solder.
Resistance change: not to exceed ±20% (*)
5 Soldering Heat Resistance
Resistance change: not to exceed ±20% (*)
6 Dry Heat
7 Cold
8 Temperature Cycling
Normal appearance
Resistance change: not to exceed ±20% (*)
9 Damp Heat
10 High Temperature Load
(*) The resistance measurement after the test.
It is measured by applying voltage less than 1.5VDC.
(by a direct current less than 10mA.) after left at 25±2°C for 2 hours.
(**) Above mentioned soldering is done under the following conditions at our side.
s'LASS %POXY0#BOARD
s3TANDARDLANDDIMENSIONS
s2ECOMMENDABLESOLDERPASTE
s2ECOMMENDABLESOLDERPROFILE
Above conditions are mentioned in Notice.
'LASS%POXY0#"
JIS C 5102 term 8.2
Soldered PTC to PCB (**)
Vibration: 10-55-10Hz (1 min.)
Width: 1.5mm
Vibrate for 2 hours. in each of 3 mutually
perpendicular plane for a total of 6 hours
JIS C 60068-2-20(1996)
Solder temp.: 230±5°C
Solder: Sn63%/Pb37% (or 60%/40%)
Soaking time: 3±0.5 seconds
Soaking position: Until a whole electrode is soaked.
JIS C 60068-2-20 (1996)
Solder temp.: 260±5°C
Solder: Sn63%/Pb37% (or 60%/40%)
Flux: containing less than 0.2wt% of chlorine
Soaking time: 10±0.5 seconds
Soaking position: Until a whole electrode is soaked.
Preheating: 150±5°C, 3 minutes
Soldered PTC to PCB. (**)
150±2°C leave for 1000±12 hours
Soldered PTC to PCB. (**)
-20±3°C leave for 1000±12 hours
JIS C 5102 term 9.3
Soldered PTC to PCB. (**)
Times: 5 cycles
Step
1
2
3
4
Temp. (°C)
-20+0, -3
room temp.
+150+3, -0
room temp.
Time (min.)
30
10 to 15
30
10 to 15
Soldered PTC to PCB. (**)
+40±2°C, 90-95%RH leave for 500±8 hours
Soldered PTC to PCB. (**)
85±2°C (in air), load max. operating voltage
for 1000±12 hours
81