GNM314R61A105MA13D Datasheet, PDF (4/24 Pages) Murata Manufacturing Co., Ltd. – CHIP MONOLITHIC CERAMIC CAPACITOR GNM314R61A105MA13_ (1206, X5R, 1uF, 10Vdc)

■SPECIFICATIONS AND TEST METHODS
No
Item
16 Humidit
Steady State
Specification
Temperature
Compensating Type
High Dielectric Type
The measured and observed characteristics should satisfy
the specifications in the following table.
Appearance
Capacitance
Change
Q/D.F.
No defects or abnormalities.
Within ±5% or± 0.5pF
(Whichever is larger)
30pF and over:Q≧350
10pF and over
30pF and below:Q≧275+5/2C
10pF and below:Q≧200+10C
C:Nominal Capacitance(pF)
B1,R1,R6,R7 :Within ±12.5%
F1,F5 :Within ±30%
ï¼»B1,R1,R6,R7ï¼½
W.V.: 25Vmin. :0.05max.
W.V.:16/10/6.3V :0.05max.
[F1,F5]
W.V.:25Vmin : 0.075max.
W.V.:16V : 0.1max.
I.R.
More than 1,000MW or 50W·F(Whichever is smaller)
Dielectric
Strength
17 Humidity Load
No failure.
The measured and observed characteristics should satisfy
the specifications in the following table.
Appearance
Capacitance
Change
No defects or abnormalities.
Within ±7.5% or±0.75pF
(Whichever is larger)
B1,R1,R6,R7 :Within ±12.5%
F1,F5 :Within ±30%
Q/D.F.
30pF and over:Q≧200
30pF and below:Q≧100+10/3C
C:Nominal Capacitance(pF)
ï¼»B1,R1,R6,R7ï¼½
W.V.: 25Vmin. :0.05max.
W.V.:16/10/6.3V :0.05max.
[F1,F5]
W.V.:25Vmin : 0.075max.
W.V.:16V : 0.1max.
I.R.
More than 500MΩ or 25Ω·F(Whichever is smaller)
Dielectric
Strength
18 High Temperature
Load
No failure.
The measured and observed characteristics should satisfy
the specifications in the following table.
Appearance No defects or abnormalities.
Capacitance Within ±3% or ±0.3pF
Change
(Whichever is larger)
B1,R1,R6,R7 :Within ±12.5%
F1,F5 :Within ±30%
Q/D.F.
I.R.
30pF and over:Q≧350
ï¼»B1,R1,R6,R7ï¼½
10pF and over
W.V.: 25Vmin. :0.04max.
30pF and below: Q≧275+5/2C W.V.:16/10/6.3V :0.05max.
10pF and below:Q≧200+10C
[F1,F5]
C:Nominal Capacitance (pF) W.V.:25Vmin : 0.075max.
W.V.:16V : 0.1max.
More than 1,000MW or 50W·F(Whichever is smaller)
Test Method
Set the capacitor at 40±2℃ and in 90 to 95% humiduty
for 500±12 hours.
Remove and set for 24±2 hours at room temperature, then
measure.
Apply the rated voltage at 40±2℃ and 90 to 95% humidity
for 500±12 hours. Remove and set for 24±2 hours at room
temprature then muasure. The charge/discharge current is
less than 50mA.
Apply 200% of the rated voltage at the maximum operating
temperature ±3℃ for 1000±12 hours.
Set for 24±2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
ï½¥Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage at the maximun operating
temperature ±3C for one hour. Remove and set for
24±2 hours at room temperature.
Perform initial measurement.
Table A-1
Char.
Nominal Values
(ppm/C) *
Capacitance Change from 20C (%)
-55
-25
-10
Max. Min. Max. Min. Max. Min.
2C
0±60
0.82 -0.45 0.49 -0.27 0.33 -0.18
* Nominal values denote the temperature coefficient within a range of 20C to 125C
Table A-2
Char.
5C
Nominal Values
(ppm/C) *
0±30
Capacitance Change from 25C (%)
-55
-30
-10
Max. Min. Max. Min. Max. Min.
0.58 -024 0.40 -0.17 0.25 -0.11
* Nominal values denote the temperature coefficient within a range of 25C to 125C
JEMCCS-0001K
4