PIC16F1938 Datasheet, PDF (387/452 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers

PIC16(L)F1938/9
30.3 DC Characteristics: PIC16(L)F1938/39-I/E (Power-Down)
PIC16LF1938/39
PIC16F1938/39
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D023
— 0.06 1.0
8.0
A
1.8 WDT, BOR, FVR, and T1OSC
— 0.08 2.0
9.0
A
3.0 ^{disabled, all Peripherals Inactive}
D023
—
15
35
—
18
40
45
A
1.8 WDT, BOR, FVR, and T1OSC
50
A
3.0 ^{disabled, all Peripherals Inactive}
—
19
45
55
A
5.0
D024
—
0.5
6.0
9.0
A
1.8 LPWDT Current (Note 1)
—
0.8
7.0
10
A
3.0
D024
—
16
35
45
A
1.8 LPWDT Current (Note 1)
—
19
40
50
A
3.0
—
20
45
55
A
5.0
D025
—
8.5
23
30
A
1.8 FVR current
—
8.5
26
33
A
3.0
D025
—
32
55
70
A
1.8 FVR current (Note 4)
—
39
72
80
A
3.0
—
70
100
110
A
5.0
D026
—
7.5
25
28
A
3.0 BOR Current (Note 1)
D026
—
34
57
67
A
3.0 BOR Current (Note 1, Note 4)
—
67
120
130
A
5.0
D027
—
0.6
5.0
9.0
A
1.8 T1OSC Current (Note 1)
—
1.8
6.0
12
A
3.0
D027
—
16
40
45
A
1.8 T1OSC Current (Note 1)
—
21
45
50
A
3.0
—
25
50
55
A
5.0
*
†
Legend:
Note 1:
2:
3:
4:
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
TBD = To Be Determined
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
A/D oscillator source is FRC.
0.1 F capacitor on VCAP (RA0).
 2011 Microchip Technology Inc.
Preliminary
DS41574A-page 387