MLX90365 Datasheet, PDF (8/35 Pages) Melexis Microelectronic Systems – Triaxis® Position Sensor IC

MLX90365
Triaxis® Position Sensor IC
7. MLX90365 Electrical Specification
Operating Parameters at Nominal Supply Voltage (unless otherwise specified) and for T_A as specified by
the Temperature suffix (E or K or L).
Parameter
Symbol
Test Conditions
Min Typ Max Units
Nominal Supply Voltage
VDD
4.5
5
5.5
V
Supply Current⁽²⁾
Power saving Enabled, All modes
Idd
For Outmode=1
Power saving Disabled, All modes
For Outmode=1
10⁽³)
6
10⁽³⁾
mA
12
8
12
Isurge Current⁽⁴⁾
Isurge
20
mA
Power-On reset ( rising )
HPOR_LH Refer to internal voltage Vdig
2 2.25 2.5
V
Power-On reset Hysteresis HPOR_Hyst
50
200
mV
Start-up Level ( rising )
MT4V LH
3.8 4.0
4.2
V
Start-up Hysteresis
MT4V Hyst
50
200
mV
PTC Entry Level ( rising )
MT7V_LH
5.8 6.2
6.6
V
PTC Entry Level Hysteresis MT7V_Hyst
50
200
mV
Output Short Circuit Current
Output Load Analog
Vout = 0 V
Ishort
Vout = 5 V
Vout = 18 V (TA = 25°C)
Pull-down to Ground
RL
Pull-up to 5V
15
mA
15
mA
18
mA
4.7 10
∞
kΩ
4.7 10
∞
kΩ
Pull-down to Ground
1
Output Load PWM
RL_PWM _{Pull-up to 5V}
1
kΩ
kΩ
Analog Saturation Output Level
Vsat_lo
Vsat_hi
Pull-up load RL ≥ 10 kΩ to 5 V
Pull-up load RL ≥ 5 kΩ to 18V
Pull-down load RL ≥ 5 kΩ
Pull-down load RL ≥ 10 kΩ
0.5
2
2
3
%VDD
95
97
97.5 98.5
%VDD
Pull-up load RL_PWM ≤ 1 kΩ to 5V
98
Digital Saturation Level
Open drain Output
(RL_PWM to Vbat)
Pull-up load RL_PWM ≤ 1 kΩ to 14V
95
Vo_min
Pull-up load RL_PWM ≤ 1 kΩ to 18V
Pull-up load RL_PWM ≤ 5.6 kΩ to 5V
90
96
Pull-up load RL_PWM ≤ 5.6 kΩ to 14V 85
%Vbat
Pull-up load RL_PWM ≤ 5.6 kΩ to 18V 73
Dsat_lo ^{Pull-up load RL ≥ 10 kΩ to 5 V}
Active Diagnostic Output Level
Pull-up load RL ≥ 5 kΩ to 18V
0.5
2
2
3
%VDD
Digital Saturation Output Level _{Dsat_hi Pull-down load RL ≥ 5 kΩPull-down}
95
97
load RL ≥ 10 kΩ
%VDD
2 _{For the dual version, the supply current is multiplied by 2.}
3 _{To reach 10mA, the power saving optionshould be enabled. This option switches off and on internal blocks dynamically. It can}
be disabled in case of extreme emission requirements or if an analog output is required with a resistor on either supply or output
line. .
4 _{The specified value is valid during early start-up time only; the current might dynamically exceed the specified value, shortly,}
during the Start-up phase.
MLX90365
Rev. 5.7
Page 8 of 35
Datasheet
Jan. 22, 16