MAX14811 Datasheet, PDF (4/20 Pages) Maxim Integrated Products – Dual, Unipolar/Bipolar, High-Voltage Digital Pulsers with Fault Condition Management

MAX14811
Dual, Unipolar/Bipolar, High-Voltage Digital Pulsers
with Fault Condition Management
ELECTRICAL CHARACTERISTICS* (continued)
(V_DD = +2.7V to +6V, V_{CC_}= +4.75V to +12.6V, V_{EE_}= -12.6V to -4.75V, V_{NN_}= -200V to 0, V_{PP_} = 0 to (V_{NN_}+ 200V), V_SS P the lower
of V_NN1 or V_NN2, T_A = T_J = T_MIN to T_MAX, unless otherwise noted. Typical values are at T_A = +25NC.) (Note 3)
PARAMETER
SYMBOL
LOGIC INPUTS (EN_, SHDN, INN_, INP_, INC_)
Low-Level Input Voltage
V_IL
CONDITIONS
High-Level Input Voltage
Logic-Input Capacitance
Logic-Input Leakage (INC_,
SHDN, EN_ Only)
Pulldown Resistor (INN_, INP_
Only)
OUTPUT (OUT_)
OUT_ Output-Voltage Range
Low-Side Small-Signal Output
Impedance
High-Side Small-Signal Output
Impedance
Low-Side Output Current
High-Side Output Current
Off-Output Capacitance
Off-Output Leakage Current
Low-Side Signal-Clamp Output
Impedance
High-Side Signal-Clamp Output
Impedance
Low-Side Gate Short Impedance
V_IH
C_IN
I_IN
R_PIN
V_IN = 0V or V_DD
V_{OUT_}
No load at OUT_
100mA load
R_SOL
R_HOS
I_OL
I_OH
C_O(OFF)
I_LK
R_CLS
R_CHS
R_LSH
I_{ON_} = -100mA, V_{CC_} = +12V Q5%,
DC-coupled
I_{ON_} = -100mA, V_{CC_} = +5V Q5%,
DC-coupled
I_{OP_} = -100mA, V_{CC_} = +12V Q5%,
DC-coupled
I_{OP_} = -100mA, V_{CC_} = +5V Q5%,
DC-coupled
V_{CC_} = +12V Q5%, V_{OUT_} - V_{NN_} = 100V
V_{CC_} = +12V Q5%, V_{OUT_} - V_{PP_} = 100V
OP_, ON_, OCP_ and OCN_ connected
together, V_{PP_} = +100V, V_{NN_} = -100V
V_{PP_} = +100V, V_{NN_} = -100V, V_{EN_} = 0V,
V_{OUT_} = -100V to +100V
I_{OCN_} = -100mA, DC-coupled,
V_{CC_} = +12V Q5%, V_{EE_} = -V_{CC_}
I_{OCN_} = -100mA, DC-coupled,
V_{CC_} = +5V Q5%, V_{EE_} = -V_{CC_}
I_{OCP_} = -100mA, DC-coupled,
V_{CC_} = +12V Q5%, V_{EE_} = -V_{CC_}
I_{OCP_} = -100mA, DC-coupled,
V_{CC_} = +5V Q5%, V_{EE_} = -V_{CC_}
V_{CC_} = +12V Q5%, V_{EE_} = -V_{CC_,}
I_{CGN_} = 10mA, V_{EN_} = 0V
V_{CC_} = +12V Q5%, V_{EE_} = -V_{CC_,}
I_{CGN_} = 10mA, V_{EN_} = V_DD
MIN TYP
0.75 x
V_DD
5
-1
7
10
V_{NN_}
V_NN_ +
2.5
9
9.5
10.5
12
1.3
2.5
1.3
2
45
-1
22
24
28
38
5
7.5
MAX UNITS
0.25 x
V_DD
V
V
pF
+1
FA
13
kI
V_{PP_}
V_PP_ -
V
2.5
17
I
18
17
I
18
A
A
pF
+1
FA
50
I
65
50
I
65
100
I
10
kI
����������������������������������������������������������������� Maxim Integrated Products   4
*The parametic values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.