MAX15022_11 Datasheet, PDF (23/28 Pages) Maxim Integrated Products – Dual, 4A/2A, 4MHz, Step-Down DC-DC Regulator with Dual LDO Controllers

Dual, 4A/2A, 4MHz, Step-Down DC-DC
Regulator with Dual LDO Controllers
The input capacitance to the base of the pass transistor
(C_QIN), any external base-to-emitter capacitance (C_BE,
see the Base-Drive Noise Reduction section), the tran-
sistor’s input resistance (R_IN), and the base-to-emitter
pullup resistor (R_{P_}) set a second pole:
( ) ^fPOLE2[kHz]
=
2π
C_BE
+
C_QIN
1
[µF]
× R_TOTAL[kΩ]
where R_TOTAL = R_IN R_P1/2.
To maintain the stability, at a minimum the following
condition must be satisfied:
A_V × f_POLE1 < f_POLE2
i.e., the second pole must occur above the unity-gain
crossover. At heavy output load, we can simplify as fol-
lows:
R_OUT3/4 << R_1FB3/4 + R_2FB3/4
C_BE << C_QIN ≈ g_m−PNP × τ_F
R_P1/2
>>
R_IN
≈
β
g_m−PNP
And hence, the output capacitance (C_OUT3/4) must sat-
isfy the following equation:
C_OUT3/4 > α × g_{C_} × τ_F × β²
where:
α=
R_2FB3/4
R_1FB3/4 + R_2FB3/4
ß is the current gain of the PNP transistor, g_{C_} is the
transconductance of the internal amplifier (1.2mA/mV
typical), and τ_F is the forward transit time of the PNP
transistor. For example, using a PNP transistor with a ß
of 120, τ_F of 400ps, g_{C_} = 1.2mA/mV, and α = 0.5 for a
1.2V output voltage, C_OUT must be at least 3.9µF.
If the second pole occurs well after unity-gain crossover,
the linear regulator remains stable. If not, then increase
the output capacitance, C_OUT3/4, such that:
f_POLE2 > 2 × f_{COUT_}
If the output capacitor is a high-ESR capacitor, then
cancel the ESR zero with a pole at FB3/4. This is
accomplished by adding a capacitor (C_FB3/4) from
FB3/4 to ground, such that:
C_FB3/4[µF]
=
2π
×
(R_1FB3/4
1
R_2FB3/4)[kΩ] ×
f_ESR[kHz]
For a sufficiently low output capacitance, choose a fast
PNP transistor without an excessively high ß. Note,
selecting a transistor with a ß that is too low can
adversely impact load regulation.
Output 3 and Output 4 Capacitors
Connect C_OUT (as determined above) between the lin-
ear regulator’s output and ground, as close as possible
to the MAX15022 and the external pass transistors.
Depending on the selected pass transistor, larger
capacitor values may be required for stability (see the
Stability Requirement section).
Once the minimum capacitor value for stability is deter-
mined, verify that the linear regulator’s output does not
contain excessive noise. Although adequate for stabili-
ty, small capacitor values can provide too much band-
width, making the linear regulator sensitive to noise.
Larger capacitor values reduce the bandwidth, thereby
reducing the regulator’s noise sensitivity.
Base-Drive Noise Reduction
The high-impedance base driver is susceptible to sys-
tem noise, especially when the linear regulator is lightly
loaded. Capacitively coupled switching noise or induc-
tively coupled EMI on the base drive may cause fluctu-
ations in the base current, which appear as noise on
the linear regulator’s output. To avoid this, keep the
base-driver traces away from the step-down converter
and as short as possible to minimize noise coupling.
A bypass capacitor (C_BE) can be placed across the
base-to-emitter resistor. This bypass capacitor, in addi-
tion to the transistor’s input capacitance, reduces the
frequency of the second pole (f_POLE2) that could desta-
bilize the linear regulator. Therefore, the stability
requirements determine the maximum base-to-emitter
capacitance (C_BE) that can be added. A capacitance
in the range of 470pF to 2200pF is recommended.
______________________________________________________________________________________ 23