|
DS4830_13 Datasheet, PDF (1/30 Pages) Maxim Integrated Products – Optical Microcontroller | |||
|
DS4830
Optical Microcontroller
General Description
The DS4830 provides a complete optical control, calibra-
tion, and monitor solution based on a low-power, 16-bit,
microcontroller core, providing program and RAM data
memory. I/O resources include a fast/accurate analog-to-
digital converter (ADC), fast comparators with an internal
comparison digital-to-analog converter (DAC), 12-bit
DACs, 12-bit PWMs, internal and external temperature
sensors, fast sample/hold, I2C slave host interface, and
a multiprotocol serial master/slave interface.
Direct connection of diode-connected transistors, used
as remote temperature sensors, is supported as well as
expansion to additional external digital temperature sen-
sor ICs using the on-chip master I2C interface. An inde-
pendent slave I2C interface facilitates communication to
a host microprocessor in addition to password-protected
in-system reprogramming of the on-chip flash.
Firmware development is supported by third-party highly
versatile C-compilers and development software that
programs flash and performs in-circuit debug through
the integrated JTAG interface and associated hardware.
Applications
PON Diplexers and Triplexers: GPON, 10GEPON,
XPON OLT, ONU
Optical Transceivers: XFP, SFP, SFP+, QSFP,
40G, 100G
Ordering Information appears at end of data sheet.
Typical Application Circuit appears at end of data sheet.
Features
S 16-Bit Low-Power Microcontroller
S 36 kWords Total Program Memory
ï² 32 kWords Flash Program Memory
ï² 4 kWords ROM Program Memory
S 1 kWords Data RAM
S 8 DAC Channels
ï² 12-Bit Buffered Voltage DACs
ï² Internal or External Reference
S 10 PWM Channels
ï² Boost/Buck DC-DC Control with Support for
7-Bit to 12-Bit Resolution and 1MHz Switching
Frequency
ï² Supports 4-Channel TECC H-Bridge Control
S 8-Bit Fast Comparator with 16-Input Mux
ï² 1.6µs per Comparison
S 13-Bit A/D Converter with 26-Input Mux (27ksps)
S Temperature Measurement Analog Front-End
ï² Internal Temperature Sensor, ±3NC
ï² 0.0625NC Resolution
ï² Supports Two External Temperature Sensors
ï² Differential Rail-Rail Inputs
S 31 GPIO Pins
S Maskable Interrupt Sources
S Internal 20MHz Oscillator, CPU Core Frequency 10MHz
ï² 4% Accurate from 0NC to +50NC
S Up to 133MHz External Clock for PWM and Timers
S Slave Communication Interface: SPI or 400kHz
I2C-Compatible 2-Wire
S Master Communication Interface: SPI, 400kHz I2C-
Compatible, or Maxim 3-Wire Laser Driver
S I2C and JTAG Bootloader
S Two 16-Bit Timers
S 2.97V to 3.63V Operating Voltage Range
S Brownout Monitor
S JTAG Port with In-System Debug and Programming
S Low Power Consumption (16mA) with All Analog
Active
For related parts and recommended products to use with this part, refer to: www.maximintegrated.com/DS4830.related
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may
be simultaneously available through various sales channels. For information about device errata, go to: www.maximintegrated.com/errata.
For pricing, delivery, and ordering information, please contact Maxim Direct at
1-888-629-4642, or visit Maxim Integratedâs website at www.maximintegrated.com.
19-5934; Rev 2; 6/13
|
▷ |