LTC3731_15 Datasheet, PDF (25/34 Pages) Linear Technology – 3-Phase, 600kHz, Synchronous Buck Switching Regulator Controller

LTC3731
APPLICATIONS INFORMATION
1) Are the signal and power ground paths isolated? Keep
the SGND at one end of a printed circuit path thus
preventing MOSFET currents from traveling under the
IC. The IC signal ground pin should be used to hook
up all control circuitry on one side of the IC, routing
the copper through SGND, under the IC covering the
“shadow” of the package, connecting to the PGND
pin and then continuing on to the (–) plates of C_IN and
C_OUT. The V_CC decoupling capacitor should be placed
immediately adjacent to the IC between the V_CC pin and
PGND. A 1µF ceramic capacitor of the X7R or X5R type
is small enough to fit very close to the IC to minimize
the ill effects of the large current pulses drawn to drive
the bottom MOSFETs. An additional 5µF to 10µF of
ceramic, tantalum or other very low ESR capacitance
is recommended in order to keep the internal IC supply
quiet. The power ground returns to the sources of the
bottom N‑channel MOSFETs, anodes of the Schottky
diodes and (–) plates of C_IN, which should have as short
lead lengths as possible.
2) Does the IC IN⁺ pin connect to the (+) plates of C_OUT?
A 30pF to 300pF feedforward capacitor between the
IN⁺ and EAIN pins should be placed as close as pos-
sible to the IC.
3) Are the SENSE^– and SENSE⁺ printed circuit traces for
each channel routed together with minimum PC trace
spacing? The filter capacitors between SENSE⁺ and
SENSE^– for each channel should be as close as possible
to the pins of the IC. Connect the SENSE^– and SENSE⁺
pins to the pads of the sense resistor as illustrated in
Figure 12.
INDUCTOR
LTC3731
SENSE⁺
SENSE^–
1000pF
SENSE
RESISTOR
3731 F12
OUTPUT CAPACITOR
4) Do the (+) plates of C_PWR connect to the drains of the
topside MOSFETs as closely as possible? This capacitor
provides the pulsed current to the MOSFETs.
5) Keep the switching nodes, SWITCH, BOOST and TG
away from sensitive small-signal nodes (SENSE⁺,
SENSE^–, IN⁺, IN^–, EAIN). Ideally the SWITCH, BOOST
and TG printed circuit traces should be routed away and
separated from the IC and especially the “quiet” side
of the IC. Separate the high dv/dt traces from sensitive
small-signal nodes with ground traces or ground planes.
6) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
7) The 47pF to 330pF ceramic capacitor between the I_TH
pin and signal ground should be placed as close as
possible to the IC.
Figure 11 illustrates all branch currents in a three-phase
switching regulator. It becomes very clear after study-
ing the current waveforms why it is critical to keep the
high switching current paths to a small physical size.
High electric and magnetic fields will radiate from these
“loops” just as radio stations transmit signals. The output
capacitor ground should return to the negative terminal
of the input capacitor and not share a common ground
path with any switched current paths. The left half of the
circuit gives rise to the “noise” generated by a switching
regulator. The ground terminations of the synchronous
MOSFETs and Schottky diodes should return to the bot-
tom plate(s) of the input capacitor(s) with a short isolated
PC trace since very high switched currents are present.
A separate isolated path from the bottom plate(s) of the
input and output capacitor(s) should be used to tie in the IC
power ground pin (PGND). This technique keeps inherent
signals generated by high current pulses taking alternate
current paths that have finite impedances during the total
period of the switching regulator. External OPTI-LOOP
compensation allows overcompensation for PC layouts
which are not optimized but this is not the recommended
design procedure.
Figure 12. Kelvin Sensing R_SENSE
3731fc
25