LTC3731_15 Datasheet, PDF (22/34 Pages) Linear Technology – 3-Phase, 600kHz, Synchronous Buck Switching Regulator Controller

LTC3731
APPLICATIONS INFORMATION
this recovery time, V_OUT can be monitored for excessive
overshoot or ringing, which would indicate a stability
problem. The availability of the I_TH pin not only allows
optimization of control loop behavior, but also provides
a DC coupled and AC filtered closed-loop response test
point. The DC step, rise time and settling at this test
point truly reflects the closed-loop response. Assuming
a predominantly second order system, phase margin and/
or damping factor can be estimated using the percentage
of overshoot seen at this pin. The bandwidth can also be
estimated by examining the rise time at the pin. The I_TH
external components shown in the Figure 1 circuit will
provide an adequate starting point for most applications.
The I_TH series R_C-C_C filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.2 to 5 times their suggested values) to maximize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be decided upon
because the various types and values determine the loop
feedback factor gain and phase. An output current pulse
of 20% to 80% of full load current having a rise time of
<2µs will produce output voltage and I_TH pin waveforms
that will give a sense of the overall loop stability without
breaking the feedback loop. The initial output voltage step,
resulting from the step change in output current, may
not be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This is
why it is better to look at the I_TH pin signal which is in the
feedback loop and is the filtered and compensated control
loop response. The gain of the loop will be increased by
increasing R_C and the bandwidth of the loop will be in-
creased by decreasing C_C. If R_C is increased by the same
factor that C_C is decreased, the zero frequency will be kept
the same, thereby keeping the phase the same in the most
critical frequency range of the feedback loop. The output
voltage settling behavior is related to the stability of the
closed-loop system and will demonstrate the actual overall
supply performance.
A second, more severe transient is caused by switching
in loads with large (>1µF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C_OUT, causing a rapid drop in V_OUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If C_LOAD is greater
than 2% of C_OUT , the switch rise time should be controlled
so that the load rise time is limited to approximately
1000 • R_SENSE • C_LOAD. Thus a 250µF capacitor and a 2mΩ
R_SENSE resistor would require a 500µs rise time, limiting
the charging current to about 1A.
Automotive Considerations: Plugging into the
Cigarette Lighter
As battery-powered devices go mobile, there is a natural
interest in plugging into the cigarette lighter in order to
conserve or even recharge battery packs during operation.
But before you connect, be advised: you are plugging into
the supply from hell. The main battery line in an automobile
is the source of a number of nasty potential transients,
including load dump, reverse battery and double battery.
Load dump is the result of a loose battery cable. When the
cable breaks connection, the field collapse in the alterna-
tor can cause a positive spike as high as 60V which takes
several hundred milliseconds to decay. Reverse battery is
just what it says, while double battery is a consequence of
tow-truck operators finding that a 24V jump start cranks
cold engines faster than 12V.
The network shown in Figure 10 is the most straightforward
approach to protect a DC/DC converter from the ravages
of an automotive battery line. The series diode prevents
current from flowing during reverse battery, while the
transient suppressor clamps the input voltage during
load dump. Note that the transient suppressor should not
conduct during double-battery operation, but must still
clamp the input voltage below breakdown of the converter.
Although the IC has a maximum input voltage of 32V on
3731fc
22