LTC3788 Datasheet, PDF (17/32 Pages) Linear Technology – 2-Phase, Dual Output Synchronous Boost Controller

LTC3788
APPLICATIONS INFORMATION
Sense Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 2a. R_SENSE is chosen based on the required
output current.
The current comparator has a maximum threshold
V_SENSE(MAX). When the ILIM pin is grounded, floating or
tied to INTV_CC, the maximum threshold is set to 50mV,
75mV or 100mV, respectively. The current comparator
threshold sets the peak of the inductor current, yielding
a maximum average output current, I_MAX, equal to the
peak value less half the peak-to-peak ripple current, ΔI_L.
To calculate the sense resistor value, use the equation:
R_SENSE
=
V_SENSE(MAX)
I_MAX
+
ΔI_L
2
When using the controller in low V_IN and very high voltage
output applications, the maximum output current level will
be reduced due to the internal compensation required to
meet stability criterion for boost regulators operating at
greater than 50% duty factor. A curve is provided in the
Typical Performance Characteristics section to estimate
this reduction in peak output current level depending upon
the operating duty factor.
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3788 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 2b. The DCR of the inductor can be less than 1mΩ
for high current inductors. In a high current application
requiring such an inductor, conduction loss through a
sense resistor could reduce the efficiency by a few percent
compared to DCR sensing.
If the external R1||R2 • C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature. Consult the
manufacturer’s data sheets for detailed information.
Using the inductor ripple current value from the inductor val-
ue calculation section, the target sense resistor value is:
R_SENSE(EQUIV)
=
V_SENSE(MAX)
I_MAX
+
ΔI_L
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the maximum current sense threshold
(V_SENSE(MAX)).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of resistance, which is approximately 0.4%/°C. A
conservative value for the maximum inductor temperature
(T_L(MAX)) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value, use the divider ratio:
R_D
=
R_SENSE(EQUIV)
DCR_MAX at T_L(MAX)
C1 is usually selected to be in the range of 0.1μF to 0.47μF.
This forces R1|| R2 to around 2k, reducing error that might
have been caused by the SENSE⁺ pin’s ±1μA current.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
R1|| R2 =
(DCR
L
at 20°C) • C1
The sense resistor values are:
R1= ^{R1|| R2} ; R2 = ^{R1• RD}
R_D
1− R_D
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at V_IN = 1/2 V_OUT:
P_LOSS
R1 =
(V_OUT
− V_IN)
R1
•
V_IN
3788f
17