LTC3854_15 Datasheet, PDF (16/28 Pages) Linear Technology – Small Footprint, Wide VIN Range Synchronous Step-Down DC/DC Controller

LTC3854
APPLICATIONS INFORMATION
sense voltage is progressively lowered from its maximum
programmed value to 25% of the maximum value. Foldback
current limiting is disabled during soft-start.
Minimum and Maximum On-Time Considerations
Minimum on-time t_ON(MIN) is the smallest time duration
that the LTC3854 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that
V_OUT
V_IN • f_SW
> t_ON(MIN)
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
The minimum on-time for the LTC3854 is approximately
75ns. However, as the peak sense voltage decreases the
minimum on-time gradually increases. This is of particu-
lar concern in forced continuous applications with low
ripple current at light loads. If the duty cycle drops below
the minimum on-time limit in this situation, a significant
amount of cycle skipping can occur with correspondingly
larger current and voltage ripple.
Care should also be taken for applications where the duty
cycle can approach the maximum given in the data sheet
(98%). In all low dropout applications, such as V_OUT = 5V
and V_IN(MIN) = 4.5V, careful selection of the bottom syn-
chronous MOSFET is required. For applications where the
input voltage can drop below the targeted output voltage,
and subsequently ramp up, a low threshold synchronous
MOSFET with a small total gate charge should be chosen.
This selection for the bottom synchronous MOSFET will
insure that the bottom gate minimum on-time is sufficient
in dropout to allow for the initial boost capacitor refresh
that is needed to adequately turn on the top side driver and
begin the switching cycle. Another method to guarantee
performance in this type of application is to increase the
minimum output load to 50mA. This minimum load will
allow the user to choose larger MOSFETs for delivery of
16
large currents when V_IN is in the normal operating range
yet still provide an adequate safety margin and good overall
performance in dropout with a slow ramping V_IN.
Efficiency Considerations
The efficiency of a switching regulator is equal to the
output power divided by the input power times 100%. It
is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percent-
age of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC3854 circuits: 1) IC V_IN current, 2) INTV_CC
regulator current, 3) I²R losses, 4) Topside MOSFET
transition losses.
1. The V_IN current is the DC supply current given in the
Electrical Characteristics table, which excludes MOSFET
driver and control currents. V_IN current typically results
in a small (<0.1%) loss.
2. INTV_CC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge dQ moves
from INTV_CC to ground. The resulting dQ/dt is a cur-
rent out of INTV_CC that is typically much larger than the
control circuit current. In continuous mode, I_GATECHG
= f(Q_T + Q_B), where Q_T and Q_B are the gate charges of
the topside and bottom side MOSFETs.
3. I²R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor.
In continuous mode, the average output current flows
through L and R_SENSE, but is “chopped” between the
topside MOSFET and the synchronous MOSFET. If the
two MOSFETs have approximately the same R_DS(ON),
then the resistance of one MOSFET can simply be
summed with the resistances of L and R_SENSE to obtain
3854fb