4000 Datasheet, PDF (24/37 Pages) C&D Technologies – Toroidal Surface Mount Inductors

24 | Keysight | InfiniiVision 4000 X-Series Oscilloscopes - Data Sheet
Oscilloscope Experience Redefined:
InfiniiVision 4000 X-Series Performance Characteristics
DSO and MSO 4000 X-Series oscilloscopes
4000 X-Series specification overview
4022A
4024A
4032A
4034A 4052A
4054A
4104A
4154A
Bandwidth ¹ (–3 dB)
200 MHz
350 MHz
500 MHz
1 GHz
1.5 GHz ³
All-channel real-time bandwidth
200 MHz
350 MHz
500 MHz
1 GHz
1 GHz
Calculated rise time (10 to 90%)
≤ 1.75 ns
≤ 1 ns
≤ 700 ps
≤ 450 ps ≤ 300 ps
Input channels
DSOX
2
4
2
4
2
4
4
4
MSOX
2 + 16
4 + 16
2 + 16
4 + 16
2 + 16
4 + 16
4 + 16
4 + 16
Maximum sample rate
5 GSa/s half channel, 2.5 GSa/s all channel
Maximum memory depth Standard 4 Mpts, standard segmented memory
Display size and type
12.1-inch high-definition capacitive touch display
Waveform update rate
> 1 million waveforms per second
System bandwidth with N2894A standard 200 MHz 200 MHz 350 MHz 350 MHz 500 MHz 500 MHz 700 MHz 700 MHz
passive probe
Vertical system analog channels
Hardware bandwidth limits
Approximately 20 MHz (selectable)
Input coupling
AC, DC
Input impedance
Selectable: 1 MΩ ± 1% (16 pF), 50 Ω ± 1.5%
Input sensitivity range
200 MHz ~ 500 MHz models: 1 mV/div to 5 V/div ² (1 MΩ and 50 Ω)
1 and 1.5 GHz models: 1 mV/div to 5 V/div ² (1 MΩ), 1 mV/div to 1 V/div (50 Ω)
Vertical resolution
8 bits (measurement resolution is 12 bits with averaging)
Maximum input voltage
1 MΩ
300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk. Frequency derating (assumes sine
wave input): 400 Vpk until 40 kHz. Then derates at 20 db/dec until 6 Vpk
50 Ω
50 Ω: ≤ 5 Vrms max
DC vertical gain accuracy ¹
± 2.0% full scale ²
DC vertical offset accuracy
± 0.1 div ± 2 mV ± 1% of offset setting
Channel-to-channel isolation
200 MHz~1 GHz ≥ 40 dB from DC to maximum specified bandwidth of each model
1.5 GHz
≥ 40 dB from DC to 1 GHz, ≥ 35 dB from 1 to 1.5 GHz
Offset range
± 5 V (< 10 mV/div), ± 20 V (10 to 200 mV/div), ± 75 V (> 200 mV/div)
Vertical system digital channels
Digital input channels
16 digital (D0 to D15. Pod 1: D7 ~ D0, Pod 2: D15 ~ D8)
Thresholds
Threshold per pod
Threshold selections
TTL (+1.4 V), 5 V CMOS (+2.5 V), ECL (–1.3 V), user-defined (selectable by pod)
User-defined threshold range
± 8.0 V in 10 mV steps
Maximum input voltage
± 40 V peak CAT I; transient overvoltage 800 Vpk
Threshold accuracy ¹
± (100 mV + 3% of threshold setting)
Maximum input dynamic range
± 10 V about threshold
Minimum voltage swing
500 mVpp
Input impedance
100 kΩ ± 2% at probe tip
Input capacitance
~8 pF
Vertical resolution
1 bit
1.  Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 10 °C from firmware calibration
temperature.
2.  1 mV/div and 2 mV/div is a magnification of 4 mV/div setting. For vertical accuracy calculations, use full scale of 32 mV for 1 mV/div and 2 mV/div sensitivity
setting.
3.  1.5 GHz real time bandwidth in half-channel mode or full channel equivalent time mode.