T541D157M10AH6510 Datasheet, PDF (19/23 Pages) Kemet Corporation – T540/T541 COTS Polymer Electrolytic for High Reliability Applications, 2.5 - 63 VDC

KEMET Organic Capacitor (KO-CAP^®) – High Reliability
T540/T541 COTS Polymer Electrolytic for High Reliability Applications, 2.5 – 63 VDC
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
P2
T2
ØDo
Po ^{[10 pitches cumulative}
E1
tolerance on tape ± 0.2 mm]
Ko
B1
Ao
Bo
F
W
E2
S1
P1
T1
Center Lines of Cavity
Cover Tape
B 1 is for tape feeder reference only,
including draft concentric about B o.
User Direction of Unreeling
ØD 1
Embossment
For cavity size,
see Note 1 Table 4
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
12 mm
16 mm
D₀
D₁ Minimum
Note 1
1.0
(0.039)
1.5+0.10/−0.0
(0.059+0.004/−0.0)
1.5
(0.059)
E₁
1.75±0.10
(0.069±0.004)
P₀
4.0±0.10
(0.157±0.004)
P₂
2.0±0.05
(0.079±0.002)
2.0±0.1
(0.079±0.059)
R Reference
Note 2
25.0
(0.984)
30
(1.181)
S₁ Minimum
Note 3
T Maximum
T₁
Maximum
0.600
(0.024)
0.600
0.100
(0.024) (0.004)
Tape Size
8 mm
12 mm
16 mm
Pitch
Single (4 mm)
Single (4 mm)
& Double (8
mm)
Triple (12 mm)
B₁ Maximum
Note 4
4.35
(0.171)
8.2
(0.323)
12.1
(0.476)
Variable Dimensions — Millimeters (Inches)
E₂ Minimum
6.25
(0.246)
10.25
(0.404)
14.25
(0.561)
F
3.5±0.05
(0.138±0.002)
5.5±0.05
(0.217±0.002)
7.5±0.10
(0.295±0.004)
P₁
2.0±0.05 or 4.0±0.10
(0.079±0.002 or 0.157±0.004)
2.0±0.05 (0.079±0.002) or
4.0±0.10 (0.157±0.004) or
8.0±0.10 (0.315 ±0.004)
4.0±0.10 (0.157±0.004)
to 12.0±0.10 (0.472±0.004)
T₂ Maximum W Maximum A₀, B₀ & K₀
2.5
(0.098)
8.3
(0.327)
4.6
(0.181)
12.3
(0.484)
Note 5
8.0 (0.315)
16.3
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment
location and hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 4).
3. If S₁ < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B₁ dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A₀, B₀ and K₀ shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see
Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2077_T540-541 • 11/29/2016 19