IS61QDP2B22M18A Datasheet, PDF (3/33 Pages) Integrated Silicon Solution, Inc – 1Mx36 and 2Mx18 configuration available

IS61QDP2B22M18A/A1/A2
IS61QDP2B21M36A/A1 /A2
Ball Description
Symbol
K, K#
CQ, CQ#
Doff#
QVLD
SA
D0 - Dn
Type
Input
Output
Input
Output
Input
Input
Q0 - Qn
W#
R#
BW_x#
V_REF
V_DD
V_DDQ
V_SS
Output
Input
Input
Input
Input
reference
Power
Power
Ground
ZQ
Input
TMS, TDI, TCK Input
TDO
Output
NC
N/A
ODT
Input
Description
Input clock: This input clock pair registers address and control inputs on the rising edge of K, and
registers data on the rising edge of K and the rising edge of K#. K# is ideally 180 degrees out of
phase with K. All synchronous inputs must meet setup and hold times around the clock rising
edges. These balls cannot remain VREF level.
Synchronous echo clock outputs: The edges of these outputs are tightly matched to the
synchronous data outputs and can be used as a data valid indication. These signals are free
running clocks and do not stop when Q tri-states.
DLL disable and reset input : when low, this input causes the DLL to be bypassed and reset the
previous DLL information. When high, DLL will start operating and lock the frequency after tCK lock
time. The device behaves in one clock read latency mode when the DLL is turned off. In this mode,
the device can be operated at a frequency of up to 167 MHz.
Valid output indicator: The Q Valid indicates valid output data. QVLD is edge aligned with CQ and
CQ#.
Synchronous address inputs: These inputs are registered and must meet the setup and hold times
around the rising edge of K. These inputs are ignored when device is deselected.
Synchronous data inputs: Input data must meet setup and hold times around the rising edges of K
and K# during WRITE operations. See BALL CONFIGURATION figures for ball site location of
individual signals.
The x18 device uses D0~D17. D18~D35 should be treated as NC pin.
The x36 device uses D0~D35.
Synchronous data outputs: Output data is synchronized to the respective CQ and CQ#, or to the
respective K and K# if C and /C are tied to high. This bus operates in response to R# commands.
See BALL CONFIGURATION figures for ball site location of individual signals.
The x18 device uses Q0~Q17. Q18~Q35 should be treated as NC pin.
The x36 device uses Q0~Q35.
Synchronous write: When low, this input causes the address inputs to be registered and a WRITE
cycle to be initiated. This input must meet setup and hold times around the rising edge of K.
Synchronous read: When low, this input causes the address inputs to be registered and a READ
cycle to be initiated. This input must meet setup and hold times around the rising edge of K.
Synchronous byte writes: When low, these inputs cause their respective byte to be registered and
written during WRITE cycles. These signals are sampled on the same edge as the corresponding
data and must meet setup and hold times around the rising edges of K and #K for each of the two
rising edges comprising the WRITE cycle. See Write Truth Table for signal to data relationship.
HSTL input reference voltage: Nominally VDDQ/2, but may be adjusted to improve system noise
margin. Provides a reference voltage for the HSTL input buffers.
Power supply: 1.8 V nominal. See DC Characteristics and Operating Conditions for range.
Power supply: Isolated output buffer supply. Nominally 1.5 V. See DC Characteristics and
Operating Conditions for range.
Ground of the device
Output impedance matching input: This input is used to tune the device outputs to the system data
bus impedance. Q and CQ output impedance are set to 0.2xRQ, where RQ is a resistor from this
ball to ground. This ball can be connected directly to VDDQ, which enables the minimum
impedance mode. This ball cannot be connected directly to VSS or left unconnected.
In ODT (On Die Termination) enable devices, the ODT termination values tracks the value of RQ.
The ODT range is selected by ODT control input.
IEEE1149.1 input pins for JTAG.
IEEE1149.1 output pins for JTAG.
No connect: These signals should be left floating or connected to ground to improve package heat
dissipation.
ODT control; Refer to SRAM features for the details.
Integrated Silicon Solution, Inc.- www.issi.com
3
Rev. B
10/02/2014