ISL6563 Datasheet, PDF (8/19 Pages) Intersil Corporation – Two-Phase Multiphase Buck PWM Controller with Integrated MOSFET Drivers

ISL6563
voltage droop characteristic. Internal average channel
current is fed into the FB pin; the voltage thus developed
across R₁ is equal to the droop voltage.
Assuming identical power switch selection on the two
channels, Equation 4 determines the current fed out the FB
pin for output voltage droop generation:
I_FB
=
r_{---D----S----(--O----N-----)---}⋅_---I_{--P----H----A----S----E--}
R_ISEN
(EQ. 4)
where, r_DS(ON) - lower MOSFET/s’ ON resistance (@5V)
I_PHASE - average phase current
Multiphase Power Conversion
Multiphase power conversion provides a cost-effective
power solution when load currents are no longer easily
supported by single-phase converters. Although its greater
complexity presents additional technical challenges, the
multiphase approach offers cost-saving advantages with
improved response time, superior ripple cancellation, and
thermal distribution.
INTERLEAVING
The switching of each channel in an ISL6563-based
converter is timed to be symmetrically out of phase with the
other channel. As a result, the two-phase converter has a
combined ripple frequency twice the frequency of one of its
phases. In addition, the peak-to-peak amplitude of the
combined inductor currents is proportionately reduced.
Increased ripple frequency and lower ripple amplitude
generally translate to lower per-channel inductance and
lower total output capacitance for a given set of performance
specifications.
To understand the reduction of ripple current amplitude in the
multiphase circuit, examine Equation 5, which represents an
individual channel’s peak-to-peak inductor current.
I_{L, PP =}
(_---V_{----I--N-----–-----}V_{----O-----U----T---})_----⋅_----V_{----O----U-----T-}
L ⋅ f_S ⋅ V_IN
(EQ. 5)
V_IN and V_OUT are the input and output voltages,
respectively, L is the single-channel inductor value, and f_S is
the switching frequency.
The output capacitors conduct the ripple component of the
inductor current. In the case of multiphase converters, the
capacitor current is the sum of the ripple currents from each
of the individual channels. Peak-to-peak ripple current, I_PP,
decreases by an amount proportional to the number of
channels. Output-voltage ripple is a function of capacitance,
capacitor equivalent series resistance (ESR), and inductor
ripple current. Reducing the inductor ripple current allows
the designer to use fewer or less costly output capacitors
(should output ripple be an important design parameter).
I_PP=
(_---V_{----I--N-----–-----}N_------⋅_----V_{----O-----U----T---})_----⋅_----V_{----O----U-----T-}
L ⋅ f_S ⋅ V_IN
(EQ. 6)
C_IN CURRENT
Q1 D-S CURRENT
I_L2
PWM2
I_L1
PWM1
I_L1 + I_L2
FIGURE 2. PWM AND INDUCTOR-CURRENT WAVEFORMS
FOR 2-PHASE CONVERTER
Figure 2 illustrates the additive effect on output ripple
frequency. The two channel currents (I_L1 and I_L2), combine
to form the AC ripple current and the DC load current. The
ripple component has two times the ripple frequency of each
individual channel current.
Q3 D-S CURRENT
FIGURE 3. INPUT CAPACITOR CURRENT AND INDIVIDUAL
CHANNEL CURRENTS IN A 2-PHASE
CONVERTER
Another benefit of interleaving is the reduction of input ripple
current. Input capacitance is determined in a large part by
the maximum input ripple current. Multiphase topologies can
improve overall system cost and size by lowering input ripple
current and allowing the designer to reduce the cost of input
capacitance. The example in Figure 3 illustrates input
currents from a two-phase converter combining to reduce
the total input ripple current.
Figure 11, part of “Input Capacitor Selection” on page 18,
can be used to determine the input-capacitor RMS current
based on load current and duty cycle. The figure is provided
as an aid in determining the optimal input capacitor solution.
8
FN9126.8
June 10, 2010