ISL5416_14 Datasheet, PDF (57/71 Pages) Intersil Corporation – Four-Channel Wideband Programmable

ISL5416
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 (core)
4.6 (I/O’s)
Input, Output or I/O Voltage . . . . . . . . . . . . . . . . . GND -0.5V to 5.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class I
Operating Conditions
Voltage Range I/O, V_CCIO . . . . . . . . . . . . . . . . . +3.135V to +3.465V
Voltage Range core, V_CCC . . . . . . . . . . . . . . . . . . +1.71V to +1.89V
Temperature Range
Industrial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40^oC to 85^oC
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 2V to I/O V_CCIO
Thermal Information
Thermal Resistance (Typical)
θ_JA (^oC/W)
256 Lead BGA Package. . . . . . . . . . . . . . . . . . . . . .
31
w/200 LFM Air Flow . . . . . . . . . . . . . . . . . . . . . . . . .
28
w/400 LFM Air Flow . . . . . . . . . . . . . . . . . . . . . . . . .
26
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150^oC
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
For recommended soldering conditions see Tech Brief 334.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: NOTE: θ_JA is measured with the component mounted on a high effective thermal conductivity test board with “direct attach” features in free
air or with the airflow. See Tech Brief TB379 for details
Electrical Specifications V_CCC = Core supply: 1.8V ± 0.09V, T_A = -40^oC to 85^oC, Industrial
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYPICAL
MAX
UNITS
Logical One Input Voltage
Logical Zero Input Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current
V_IH
V_CCIO = 3.45V
2.0
V
V_IL
V_CCIO = 3.15V
0.8
V
V_OH
I_OH = -2mA, V_CCC = 3.15V
2.6
3
V
V_OL
I_OL = 2mA, V_CCC = 3.15V
0.1
0.4
V
I_I
V_IN = V_CCIO or GND, V_CCIO = 3.465V
-10
<1
10
µA
(NOTE 3)
Output Leakage Current
Standby Power Supply Current
(core)
I_O
V_IN = V_CCIO or GND, V_CCIO = 3.465V
-10
I_CCSB-CR V_CCC = 1.89V, See AC Test load circuit, No
CLK
10
µA
12
mA
(NOTE 6)
Standby Power Supply Current
(IO’s)
I_CCSB-IO V_CCC = 1.89V, See AC Test load circuit,
No CLK
0.75
mA
Operating Power Supply Current
(core)
Operating Power Supply Current
(IO’s)
Operating Power Supply Core
Current (typical)
Input Capacitance
I_CCOP-CR f = 80MHz, V_IN = V_CCC or GND,
V_CCC= 1.89V, See AC Test load circuit,
I_CCOP-IO f = 80MHz, V_IN = V_CCC or GND,
V_CCC = 1.89V, See AC Test load circuit,
I_CCOP-TYP f = 80MHz, V_IN = V_CCC or GND,
V_CCC = 1.89V, See AC Test load circuit,
C_IN
Freq = 1MHz, V_CCC open, all measurements
are referenced to device ground
660
150
500
(NOTE 1, 4)
5
mA
mA
mA
pF
(Note 2)
Output Capacitance
C_OUT
5
pF
(Note 2)
NOTES:
1. Power Supply current is proportional to frequency of operation and programmed configuration of the part. Typical rating for I_CCOP is 6.5 mA/MHz.
2. Capacitance: T_A = 25^oC, controlled via design or process parameters and not directly tested. Characterized upon initial design and at major
process or design changes.
3. Typical Pull-up/down resistance values are 60 kΩ.
4. Typical measured power on the Evaluation board:
•. UMTS: CLK = 76.8 MHz, Total Power = 1.1 W (core current = 500 mA; I/O current = 60 mA)
•. CDMA2000: CLK = 80 MHz, Total Power = 750 mW (core current = 360 mA; I/O current = 30 mA).
57