ISL24201_14 Datasheet, PDF (4/12 Pages) Intersil Corporation – Programmable VCOM Calibrator with EEPROM

ISL24201
Absolute Maximum Ratings
Supply Voltage
A_VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V
V_DD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4V
Input Voltage with respect to Ground
SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4V
SCL, SDA and WP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V_DD+0.3V
Output Voltage with respect to Ground
OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A_VDD
Continuous Output Current
OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
ESD Ratings
Human Body Model (Tested per JESD22-A114) . . . . . . . . . . . . . . . . . 7kV
Machine Model (Tested per JESD22-A115). . . . . . . . . . . . . . . . . . . . 250V
Charged Device Model (Tested per JESD22-C101). . . . . . . . . . . . . .1.5kV
Latch Up (Tested per JESD 78, Class II, Level A). . . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
8 Ld TDFN Package (Notes 4, 5). . . . . . . . .
53
11
Moisture Sensitivity (see Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Operating Range
A_VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 19V
V_DD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.25V to 3.6V
Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Test Conditions: V_DD = 3.3V, A_VDD = 18V, R_SET = 5kΩ, R₁ = 10kΩ, R₂ = 10kΩ, (See Figure 5); unless otherwise
specified. Typicals are at T_A = +25°C. Boldface limits apply over the operating temperature range, -40°C to +85°C.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 6)
MAX
TYP (Note 6) UNITS
DC CHARACTERISTICS
V_DD
A_VDD
A_VDD
V_DD Supply Range - Operating
A_VDD Supply Range Supporting EEPROM Programming
A_VDD Supply Range for Wide-Supply Operation
(not supporting EEPROM Programming)
2.25
10.8
4.5
3.6
V
19
V
19
V
I_DD
V_DD Supply Current
I_AVDD A_VDD Supply Current
OUT CHARACTERISTICS
WP = SCL = SDA = V_DD
WP = SCL = SDA = V_DD
37
65
µA
24
38
µA
SET_ZSE
SET_FSE
V_OUT
SET_VD
I_OUT
INL
SET Zero-Scale Error
SET Full-Scale Error
OUT Voltage Range
SET Voltage Drift
Maximum OUT Sink Current
Integral Non-Linearity
I_OUT < 0.5mA
V_SET + 0.4
7
4
±3
±8
A_VDD
±2
LSB
LSB
V
μV/°C
mA
LSB
DNL Differential Non-Linearity
I²C INPUTS AND OUTPUT
I²CV_IH
I²CV_IL
I²C_H
SDA, SCL Logic 1 Input Voltage
SDA, SCL Logic 0 Input Voltage
SDA, SCL Hysteresis
I_L
Input Leakage Current of SDA, SCL
VOL_S SDA Output Logic Low
V_IH
WP Input Logic High
V_IL
WP Input Logic Low
V_WPH WP Input Hysteresis
IL_WPN WP Input Leakage Current
I = -3mA
±1
LSB
1.44
V
0.55
V
260
mV
±1
µA
0.4
V
0.7V_DD
V
0.3V_DD
V
260
mV
-0.20
-0.5
-1
µA
4
FN7586.1
December 9, 2010