X4043-45 Datasheet, PDF (16/24 Pages) Intersil Corporation – 2.7V to 5.5V power supply operation

X4043, X4045
ABSOLUTE MAXIMUM RATINGS
Temperature under bias .................... -65°C to +135°C
Storage temperature ......................... -65°C to +150°C
Voltage on any pin with
respect to V_SS ...................................... -1.0V to +7V
D.C. output current ............................................... 5mA
Lead temperature (soldering, 10 seconds) ........ 300°C
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
-40°C
Max.
70°C
+85°C
Option
-2.7 and -2.7A
Blank and -4.5A
Supply Voltage Limits
2.7V to 5.5V
4.5V to 5.5V
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
I_CC1(1)
I_CC2(1)
I_SB1(2)
Parameter
Active supply current read
Active supply current write
Standby current AC (WDT off)
I_SB2(2) Standby current DC (WDT off)
I_SB3(2) Standby current DC (WDT on)
I_LI
Input leakage current
I_LO
Output leakage current
V_IL(3)
V_IH(3)
V_HYS
V_OL
Input LOW voltage
Input nonvolatile
Schmitt trigger input hysteresis
Fixed input level
V_CC related level
Output LOW voltage
V_CC = 2.7 to 5.5V
Min.
Max.
1.0
3.0
1
1
20
10
10
-0.5
V_CC x 0.3
V_CC x 0.7 V_CC + 0.5
Unit
mA
mA
µA
µA
µA
µA
µA
V
V
Test Conditions
V_IL = V_CC x 0.1, V_IH = V_CC x 0.9
f_SCL = 400kHz
V_IL = V_CC x 0.1, V_IH = V_CC x 0.9
f_SCL= 400kHz, SDA = open
V_CC = 1.22 x V_CC min
V_SDA = V_SCL = V_SB
Others = GND or V_SB
V_SDA =V_SCL = V_SB
Others = GND or V_SB
V_IN = GND to V_CC
V_SDA = GND to V_CC
device is in standby
0.2
.05 x V_CC
0.4
V
V
V I_OL = 3.0mA (2.7-5.5V)
I_OL = 1.8mA (2.0-3.6V)
Notes: (1) The device enters the active state after any start, and remains active until: 9 clock cycles later if the device select bits in the slave
address byte are incorrect; 200ns after a stop ending a read operation; or t_WC after a stop ending a write operation.
(2) The device goes into standby: 200ns after any stop, except those that initiate a nonvolatile write cycle; t_WC after a stop that initiates a
nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct device select bits in the slave address byte.
(3) V_IL min. and V_IH max. are for reference only and are not tested.
16
FN8118.3
December 9, 2015