IC-PR Datasheet, PDF (17/18 Pages) IC-Haus GmbH – REFLECTIVE OPTO ENCODERS

iC-PR Series
REFLECTIVE OPTO ENCODERS
Rev A3, Page 17/18
REVISION HISTORY
Rel. Rel. Date¹ Chapter
A1 2015-11-23
Modification
Initial Release
Page
all
Rel. Rel. Date¹ Chapter
Modification
A2 2016-03-31 BLOCK DIAGRAM
Block diagram updated.
ELECTRICAL
CHARACTERISTICS
204, 212: Moved value from "min." to "max." as defined as "permissible"
SIGNAL DEFINITIONS
Figure for definition of resolution in linear series added.
OPERATION MODES
Description of analog modes in Table 4 updated.
DIGITAL OPERATION MODES
Recommended EDC configuration added.
INDEX DETECTION THRESHOLD Updated description.
DEVICE OVERVIEW
Device overview table extended and updated. Changed recommendation for VZ.
Page
1
6
9
9
12
13
14
Rel. Rel. Date¹ Chapter
Modification
A3 2017-02-20 DESCRIPTION
Added "General notice on materials under excessive conditions"
PACKAGING INFORMATION
Changed footnote for TM1, TM2, TMO
ABSOLUTE MAXIMUM RATINGS G002, G004: Changed max. values
THERMAL DATA
T02: Permissible Storage Temperature Range added
T04: Corrected unit
ELECTRICAL
CHARACTERISTICS
405/407: Max./Min. value changed
605/606: Added max. value
SIGNAL DEFINITIONS
Added definition of positive direction of movement for linear series
VOLTAGE DOMAINS
Added section
ANALOG / MIXED OPERATION
MODES
Added note on VZ
Changed figure
DIGITAL OPERATION MODES
Added note on VZ
INDEX DETECTION THRESHOLD Added Note
POWER CONTROL
Description of power control added
DEVICE OVERVIEW
Changed Code Disc P/O Code, Type
Page
2
3
5
5
6,7
9
10
11
13
14
14
19
iC-Haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the
relevant current specifications on our internet website www.ichaus.com/infoletter and is automatically generated and shall be sent to registered users by email.
Copying – even as an excerpt – is only permitted with iC-Haus’ approval in writing and precise reference to source.
The data specified is intended solely for the purpose of product description and shall represent the usual quality of the product. In case the specifications contain
obvious mistakes e.g. in writing or calculation, iC-Haus reserves the right to correct the specification and no liability arises insofar that the specification was from
a third party view obviously not reliable. There shall be no claims based on defects as to quality in cases of insignificant deviations from the specifications or in
case of only minor impairment of usability.
No representations or warranties, either expressed or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder
with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In
particular, this also applies to the stated possible applications or areas of applications of the product.
iC-Haus products are not designed for and must not be used in connection with any applications where the failure of such products would reasonably be
expected to result in significant personal injury or death (Safety-Critical Applications) without iC-Haus’ specific written consent. Safety-Critical Applications
include, without limitation, life support devices and systems. iC-Haus products are not designed nor intended for use in military or aerospace applications or
environments or in automotive applications unless specifically designated for such use by iC-Haus.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
Software and its documentation is provided by iC-Haus GmbH or contributors "AS IS" and is subject to the ZVEI General Conditions for the Supply of Products
and Services with iC-Haus amendments and the ZVEI Software clause with iC-Haus amendments (www.ichaus.com/EULA).
1 _{Release Date format: YYYY-MM-DD}