|
GS81314LT19 Datasheet, PDF (4/42 Pages) GSI Technology – 144Mb SigmaDDR-IVe™ Burst of 2 Single-Bank ECCRAM™ | |||
|
◁ |
GS81314LT19/37GK-933/800
Pin Description
Symbol
Description
SA[21:0]
DQ[35:0]
QVLD[1:0]
CK, CK
KD[1:0],
KD[1:0]
CQ[1:0],
CQ[1:0]
LD
R/W
MRW
PLL
RST
ZQ
ZT
RCS
MZT[1:0]
Address â Read or write address is registered on ïCK.
Write/Read Data â Registered on ïKD and ïKD during Write operations; aligned with ïCQ and ïCQ
during Read operations.
DQ[17:0] - x18 and x36.
DQ[35:18] - x36 only.
Read Data Valid â Driven high one half cycle before valid read data.
Primary Input Clocks â Dual single-ended. Used for latching address and control inputs, for internal timing
control, and for output timing control.
Write Data Input Clocks â Dual single-ended. Used for latching write data inputs.
KD0, KD0: latch DQ[17:0] in x36, and DQ[8:0] in x18.
KD1, KD1: latch DQ[35:18] in x36, and DQ[17:9] in x18.
Read Data Output Clocks â Free-running output (echo) clocks, tightly aligned with read data outputs.
Facilitate source-synchronous operation.
CQ0, CQ0: align with DQ[17:0] in x36, and DQ[8:0] in x18.
CQ1, CQ1: align with DQ[35:18] in x36, and DQ[17:9] in x18.
Load Enable â Registered onïCK. See the Clock Truth Table for functionality.
Read / Write Enable â Registered on ïCK. See the Clock Truth Table for functionality.
Mode Register Write â Registered onïCK. Can be used synchronously or asynchronously to enable Reg-
ister Write Mode. See the State and Clock Truth Tables for functionality.
PLL Enable â Weakly pulled High internally.
PLL = 0: disables internal PLL.
PLL = 1: enables internal PLL.
Reset â Holds the device inactive and resets the device to its initial power-on state when asserted High.
Weakly pulled Low internally.
Driver Impedance Control Resistor Input â Must be connected to VSS through an external resistor RQ to
program driver impedance.
ODT Impedance Control Resistor Input â Must be connected to VSS through an external resistor RT to
program ODT impedance.
Current Source Resistor Input â Must be connected to VSS through an external 2Kï resistor to provide
an accurate current source for the PLL.
ODT Mode Select â Set the default ODT state globally for all input groups during power-up and reset. Must
be tied High or Low.
MZT[1:0] = 00: disables ODT on all input groups, regardless of PZT[1:0].
MZT[1:0] = 01: enables strong ODT on select input groups, as specified by PZT[1:0].
MZT[1:0] = 10: enables weak ODT on select input groups, as specified by PZT[1:0].
MZT[1:0] = 11: reserved.
Note: The ODT state for each input group can be changed at any time via the Configuration Registers.
Type
Input
I/O
Output
Input
Input
Output
Input
Input
Input
Input
Input
Input
Input
Input
Input
Rev: 1.02 3/2016
4/42
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2015, GSI Technology
|
▷ |