33937 Datasheet, PDF (6/47 Pages) Freescale Semiconductor, Inc – Three Phase Field Effect Transistor Pre-driver

ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings
All voltages are with respect to V_SS unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent
damage to the device.
Ratings
Symbol
Value
Unit
ELECTRICAL RATINGS
VSUP Supply Voltage
Normal Operation (Steady-state)
Transient Survival⁽¹⁾
V_SUP
V
58
-1.5 to 80
VPWR Supply Voltage
Normal Operation (Steady-state)
Transient Survival⁽¹⁾
V_PWR
V
58
-1.5 to 80
Charge Pump (PUMP, VPUMP)
VLS Regulator Outputs (VLS_, VLS_CAP)⁽²⁾
V_PUMP
-0.3 to 40
V
V_LS
-0.3 to 18
V
Logic Supply Voltage
Logic Output (INT, SO, PHASEA, PHASEB, PHASEC, OC_OUT)⁽³⁾
V_DD
-0.3 to 7.0
V
V_OUT
-0.3 to 7.0
V
Logic Input Pin Voltage (EN1, EN2, Px_HS, Px_LS, SI, SCLK, CS, RST) 10 mA
V_IN
-0.3 to 7.0
V
Amplifier Input Voltage
V_{IN_A}
V
(Both Inputs-GND), (AMP_P - GND) or (AMP_N - GND) 6.0 mA source or sink
-7.0 to 7.0
Over-current comparator threshold 10 mA
V_OC
-0.3 to 7.0
V
Driver Output Voltage⁽⁴⁾
High Side bootstrap (PA_BOOT, PB_BOOT, PC_BOOT)
V
V_BOOT
75
High Side (PA_HS_G, PB_HS_G, PC_HS_G)
V_{HS_G}
75
Low Side (PA_LS_G, PB_LS_G, PC_LS_G)
V_{LS_G}
16
Driver Voltage Transient Survival⁽⁵⁾
V
High Side (PA_HS_G, PB_HS_G, PC_HS_G, PA_HS_S, PB_HS_S,
PC_HS_S)
Low Side (PA_LS_G, PB_LS_G, PC_LS_G, PA_LS_S, PB_LS_S, PC_LS_S)
V_{HS_G}
V_{HS_S}
V_{LS_G}
-7.0 to 75.0
-7.0 to 75.0
-7.0 to 18.0
V_{LS_S}
-7.0 to 7.0
Notes
1. The device will withstand load dump transient as defined by ISO7637 with peak voltage of 80 V.
2. Normal operation of the 33937 at VPWR voltages greater than 28V can result in degradation or failure of the VLS regulator due to
transients induced during a RESET. A 20 V transient suppressor is recommended on the VLS pin (pin 51) to prevent excessive stress
under these conditions. Using the 33937A will avoid this limitation.
3. Short-circuit proof, the device will not be damaged or induce unexpected behavior due to shorts to external sources within this range.
4. This voltage should not be applied without also taking voltage at HS_S and voltage at PX_LS_S into account.
5. Actual operational limitations may differ from survivability limits. The V_LS - V_{LS_S} differential and the V_BOOT - V_{HS_S} differential must be
greater than 3.0 V to insure the output gate drive will maintain a commanded OFF condition on the output.
33937
6
Analog Integrated Circuit Device Data
Freescale Semiconductor