FOD8316 Datasheet, PDF (6/29 Pages) Fairchild Semiconductor – 2.5A Output Current, IGBT Drive Optocoupler

Isolation Characteristics
Apply over all recommended conditions, typical value is measured at T_A = 25ºC
Symbol
Parameter
Conditions
Min. Typ. Max. Units
V_ISO
R_ISO
C_ISO
Input-Output Isolation
Voltage
Isolation Resistance
Isolation Capacitance
T_A = 25ºC, R.H.< 50%, t = 1.0min,
I_I-O ≤ 10µA, 50Hz^(7)(8)(9)
V_I-O = 500V⁽⁷⁾
V_I-O = 0V, Freq = 1.0MHz⁽⁷⁾
4,243
10¹¹
1
V_RMS
Ω
pF
Notes:
7. Device is considered a two terminal device: Pins 1 to 8 are shorted together and Pins 9 to 16 are shorted together.
8. 4,243 VRMS for 1 minute duration is equivalent to 5,091 VRMS for 1 second duration.
9. The Input-Output Isolation Voltage is a dielectric voltage rating as per UL1577. It should not be regarded as an
input-output continuous voltage rating. For the continuous working voltage rating refer to your equipment level safety
specification or DIN EN/IEC 60747-5-5 Safety and Insulation Ratings Table.
Electrical Characteristics
Apply over all recommended conditions, typical value is measured at V_DD1 = 5V, V_DD2 – V_SS = 30V, V_E – V_SS = 0V,
T_A = 25°C unless otherwise specified.
Symbol
Parameter
Conditions
Min.
Typ.
Max. Units Figure
V_IN+L, V_IN-L,
V_RESETL
V_IN+H, V_IN-H,
V_RESETH
I_IN+L, I_IN-L,
I_RESETL
I_FAULTL
I_FAULTH
I_OH
I_OL
I_OLF
V_OH
V_OL
I_DD1H
I_DD1L
I_DD2H
I_DD2L
I_SH
I_SL
I_EL
I_EH
I_CHG
Logic Low Input Voltages
Logic High Input Voltages
Logic Low Input Currents
FAULT Logic Low Output Current
FAULT Logic High Output Current
High Level Output Current
Low Level Output Current
Low Level Output Current During
Fault Condition
High Level Output Voltage
Low Level Output Voltage
High Level Supply Current
Low Level Supply Current
High Level Output Supply Current
Low Level Output Supply Current
High Level Source Current
Low Level Source Current
V_E Low Level Supply Current
V_E High Level Supply Current
Blanking Capacitor Charge
Current
V_IN = 0.4V
V_FAULT = 0.4V
V_FAULT = V_DD1
V_O = V_DD2 – 3V
V_O = V_DD2 – 6V⁽¹⁰⁾
V_O = V_SS + 3V
V_O = V_SS + 6V⁽¹¹⁾
V_O – V_SS = 14V
I_O = –100mA^(12)(13)(14)
I_O = 100mA
V_IN+ = V_DD1 = 5.5V,
V_IN– = 0V
V_IN+ = V_IN- = 0V,
V_DD1 = 5.5V
V_O = Open⁽¹⁴⁾
V_O = Open
I_O = 0mA
I_O = 0mA
V_DESAT = 2V^(14)(15)
I_DSCHG
Blanking Capacitor
Discharge Current
V_DESAT = 7V
2.0
-0.5
5.0
-40
-1
-2.5
1
2.5
90
V_S – 1.0V
-0.5
-0.5
-0.13
10
-0.001
12.0
0.002
-3
3
185
V_S – 0.5V
0.1
14
2
1
0.8
0.65
0.6
-0.2
-0.25
-0.25
36
0.8
230
0.5
17
3
3
2.8
1.5
1.4
-0.37
V
V
mA
mA 1, 32
µA
32
A 2, 7, 33
A
A
3, 34
A
mA 4, 38
V 5, 7, 35
V 6, 8, 35
mA 9, 36
mA
mA 10, 11,
mA
37
mA
37
mA
37
mA 13, 37
mA
mA 12, 38
mA
38
©2010 Fairchild Semiconductor Corporation
FOD8316 Rev. 1.2.0
6
www.fairchildsemi.com