FOD8316 Datasheet, PDF (5/29 Pages) Fairchild Semiconductor – 2.5A Output Current, IGBT Drive Optocoupler

Absolute Maximum Ratings (T_A = 25ºC unless otherwise specified)
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Value
Units
T_STG
T_OPR
T_J
T_SOL
Storage Temperature
Operating Temperature
Junction Temperature
Lead Wave Solder Temperature
(no solder immersion)
-40 to +125
ºC
-40 to +100
ºC
-40 to +125
ºC
260 for 10 sec
ºC
Refer to page 27 for reflow temperature profile.
I_FAULT
I_O(PEAK)
V_E – V_SS
Fault Output Current
Peak Output Current⁽¹⁾
Negative Output Supply Voltage⁽²⁾
15
mA
3
A
0 to 15
V
V_DD2 – V_E
Positive Output Supply Voltage
-0.5 to 35 – (V_E – V_SS)
V
V_O(peak)
Gate Drive Output Voltage
-0.5 to 35
V
V_DD2 – V_SS
Output Supply Voltage
-0.5 to 35
V
V_DD1
Positive Input Supply Voltage
-0.5 to 6
V
V_IN+, V_IN- and V_RESET Input Voltages
-0.5 to V_DD1
V
V_FAULT
Fault Pin Voltage
-0.5 to V_DD1
V
V_S
Source of Pull-up PMOS Transistor Voltage
V_SS + 6.5 to V_DD2
V
V_DESAT
PD_I
PD_O
DESAT Voltage
Input Power Dissipation⁽³⁾⁽⁵⁾
Output Power Dissipation⁽⁴⁾⁽⁵⁾
V_E to V_E + 11
V
100
mW
600
mW
Notes:
1. Maximum pulse width = 10µs, maximum duty cycle = 0.2%.
2. This negative output supply voltage is optional. It’s only needed when negative gate drive is implemented. Refer to
“Dual Supply Operation – Negative Bias at Vss” on page 23.
3. No derating required across temperature range.
4. Derate linearly above 64°C, free air temperature at a rate of 10.2mW/°C
5. Functional operation under these conditions is not implied. Permanent damage may occur if the device is subjected
to conditions outside these ratings.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to absolute maximum ratings.
Symbol
Parameter
Min.
Max.
Unit
T_A
V_DD1
Ambient Operating Temperature
Input Supply Voltage⁽⁶⁾
-40
+100
ºC
3
5.5
V
V_DD2 – V_SS Total Output Supply Voltage
15
30
V
V_E – V_SS
V_DD2 – V_E
Negative Output Supply Voltage
Positive Output Supply Voltage⁽⁶⁾
0
15
V
15
30 – (V_E – V_SS)
V
V_S
Source of Pull-up PMOS Transistor Voltage
V_SS + 7.5
V_DD2
V
Note:
6. During power up or down, it is important to ensure that VIN+ remains low until both the input and output supply
voltages reaches the proper recommended operating voltages to avoid any momentary instability at the output state.
See also the discussion in the “Time to Good Power” section on page 23.
©2010 Fairchild Semiconductor Corporation
FOD8316 Rev. 1.2.0
5
www.fairchildsemi.com